User manual HOTPOINT TCF 97B 6HY

[. . . ] Choosing a programme Programmes Table The Controls Laundry, 14 Sorting your laundry Wash care labels Drying times Troubleshooting, 15 Service, 16 Spare Parts Recycling and Disposal Product data, 17 www. Eu 1 Installation GB Where to put your dryer Place your dryer at a distance from gas ranges, stoves, heaters, or cook tops because flames can damage the appliance. Minimum gap 10mm If you are going to install the appliance under a work counter, be sure to leave a Minimum gaps 10mm space between 15mm the top and any other objects on or above the machine and a 15mm space between the sides and lateral furnishings or walls. The appliance must be installed with the rear surface placed against a wall. [. . . ] Or - To change from default dryness setting, press and release the Sensor Dry button until the required level is indicated (see The Display). For full details of selections available for each programme see the Programme Tables. The START/PAUSE light is flashing green: - press the START/PAUSE button to begin. During the drying programme, you can check on your laundry and take out items that are dry while others continue drying. When you close the door again, press the START/PAUSE button in order to resume drying. (When the door is opened the START/PAUSE light will flash Amber, after the door is closed and the START/PAUSE button pressed, the START/PAUSE light will stop flashing and show green. To let you know that your programme is complete the buzzer will beep 3 times. GB Note: This tumble dryer, in compliance with new energy saving regulations, is fitted with an automatic standby system which is enabled after about 30 minutes if no activity is detected. ESSENTIAL PROGRAMMES - Programmes Table Programme Options available Dryness Levels available (default highlighted ✓ ) Hanger Dry Plus Ready to Iron* Cupboard Dry Less tangled Delay Timer Sensor Dry Hanger Dry Heat Level Timed Dry Damp Dry ✓ 1 2 3 4 5 6 Standard Cotton ✓ ✓ ✓ ✓ ✓ ✓ ✗ ✗ ✗ ✗ ✗ ✗ Shirts Bed & Bath Anti Allergy Synthetics Quick Dry ✗ ✓ ✓ ✓ ✗ ✓ ✗ ✗ ✗ - High - High - Medium - Low - High - Medium - High - Medium ✓ ✓ ✓ ✗ ✗ ● ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✗ ✗ ✓ ✗ ✗ ✗ - Medium - Low - High - Medium An Automatic programme ✓ ● An Automatic programme *Note : This option is not available with Dryness Levels ‘Iron Dry’ and ‘Damp Dry’. The duration of this programme will depend on the size of the load, the dryness setting selected and the spin speed used in your washer (see Laundry). The Standard Cotton programme to EU Regulation 392/2012 is Programme 1 selection with High Heat and Dryness Level Cupboard Dry. Loads dried using this programme are usually ready to wear, but on some heavier garments the edges may be slightly damp. Unlike other materials, the mechanism of wool shrinkage is irreversible; i. Silk ● ● ● ● This is a programme for drying your delicate silk. The duration of this programme will depend on the size and density of the load and the spin speed used in your washer. Loads dried using this programme are usually ready to use, but on some heavier garments the edges may be slightly damp. If this is the case, remove the load and open them out and then run the programme again for a short period. Delicates ● ● ● ● This is a programme for drying your delicate clothes ie. The duration of this programme will depend on the size and density of the load and the spin speed used in your washer. Loads dried using this programme are usually ready to use, but on some garments the edges may be slightly damp. If this is the case, try opening them out or turn items inside out and running the programme again for a short period. Take care with this programme DO NOT dry any items that are damaged which could result in the filling blocking the filter and air vent resulting in a fire hazard. [. . . ] If the icon is on it is just a reminder to empty the container (see Start and Programmes). — ● ● ● ● ● ● ● ● The ‘water container full’ icon is flashing and displayed but the dryer has only been running for a short period. Check the above points and run the programme again, if the results are still damp, contact the Service Centre (see Service). — The display shows a fault code F followed by one or two numbers If the display shows a fault: - Turn off and remove the plug. [. . . ]