User manual HOTPOINT TCD 93B 6H/Z1

[. . . ] Instruction booklet TUMBLE DRYER GB English, 1 F Français, 18 E Español, 35 Contents Important information, 2-3 Installation, 4 Where to put your dryer Ventilation Water drain Electrical connection Before you start using your dryer GB P GR Português, 52 EÏÏËÓÈο, 69 Dryer description, 5 The features Control panel The Display, 6-8 Start and programmes, 8-11 Choosing a programme Special programmes Programme option modifiers Table of programmes The controls TCD 93B First time you turn on your dryer you must select your preferred language see page 6 Laundry, 12-13 Sorting your laundry Wash care labels Special clothing items Drying times Warnings and Suggestions, 14 General safety Saving energy and respecting the environment Maintenance and Care, 15 Switching off the electricity Cleaning the filter after each cycle Check the drum after each cycle Empty the water container after each cycle Cleaning the condenser unit Cleaning the dryer Troubleshooting, 16 Service, 17 Disposal !Keep this instruction booklet on hand in order to refer to it when necessary. Take it with you when you move, and should you sell this appliance or pass it on to another party, make sure that this booklet is supplied along with the dryer so that the new owner may be informed about warnings and suggestions on how the appliance works. Read these instructions carefully; the following pages contain important information on installation and suggestions on how the appliance works. [. . . ] When an Automatic programme is selected, the time displayed is an estimate of the time remaining. When the programme is selected the display shows the time required to dry a full load, after around 10 minutes the controller calculates a better estimate of the cycle time. The colons between the hours and minutes in the display flash to show that the time is counting down. The display also shows if there is a problem with your dryer, if this occurs the display will show F followed by a fault code number (see Troubleshooting). — Empty Water Container (If you have plumbed your dryer to a drain this icon can be ignored, as there is no need to empty the water container). Messages are displayed to reminds you to empty the water container (see The Display). If the water container fills during a programme, the heater turns off and the dryer does a period of Cool Tumble. After this it stops and a message tells you to EMPTY THE WATER CONTAINER . You must empty the water container and restart the dryer or the clothes will not dry. After re-starting the dryer the message will take a few seconds to go out. To avoid this always empty the water container each time you use the dryer (see Maintenance). — During the drying part of the programme, the colons on the display stop flashing to show that the time has stopped counting down. The display will change to show the current status, the colons flash and count down continues. Pressing the Start/Pause button will restart a new programme from the beginning. — Note If you have a power cut, switch off the power or remove the plug. When power is restored, press the Start/Pause button and the programme will resume. Warning, after pressing the Start/Pause button , the programme cannot be changed. Select the new programme and any options required, the light will then flash green. — Option buttons These buttons are used to customise the selected programme to your requirements. Not all options are available for all programmes (see Programmes Table). If an option is not available and you press the button, the buzzer will beep 3 times. If the option is available the indicator, on the display unit above the bottom buttons, lights to show that the option has been selected. [. . . ] Do not wait for the empty water signal, always check and empty the container before starting a new drying programme (see Maintenance). This is normal, the: END OF CYCLE, EMPTY THE WATER BOTTLE message is shown as a reminder to empty the container (see The Display and Start and Programmes). — ● ● ● ● ● ● ● ● Empty water message is displayed but the dryer has only been running for a short period. Check the above points and run the programme again, if the results are still damp, contact the Service Centre (see Service). [. . . ]