User manual HOTPOINT PKLL 641 D2/IX/HAR

[. . . ] PKLL 641 D2/IX/HAR PKL 642 D2/IX/HAR Italiano Istruzioni per l’uso PIANO Sommario Istruzioni per l’uso, 1 Avvertenze, 2 Assistenza, 3 Descrizione dell’apparecchio, 4 Installazione, 5 Avvio e utilizzo, 9 Precauzioni e consigli, 9 Manutenzione e cura, 10 Anomalie e rimedi, 11 English Operating Instructions HOB Contents Operating Instructions, 1 Warnings, 2 Assistance, 3 Description of the appliance, 4 Installation, 12 Start-up and use, 16 Precautions and tips, 16 Maintenance and care, 17 Troubleshooting, 18 Avvertenze ATTENZIONE: Questo apparecchio e le sue parti accessibili diventano molto caldi durante l’uso. Warnings WARNING: The appliance and its accessible parts become hot during use. Children less than 8 years of age shall be kept away unless continuously supervised. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. [. . . ] Connecting the supply cable to the mains Install a standardised plug corresponding to the load indicated on the data plate. The appliance must be directly connected to the mains using an omnipolar circuit-breaker with a minimum contact opening of 3 mm installed between the appliance and the mains. The circuit-breaker must be suitable for the charge indicated and must comply with current electrical regulations (the earthing wire must not be interrupted by the circuit-breaker). The supply cable must not come into contact with surfaces with temperatures higher than 50°C. The installer must ensure that the correct electrical connection has been made and that it is compliant with safety regulations. Before connecting to the power supply, make sure that: • the appliance is earthed and the plug is compliant with the law. € the socket can withstand the maximum power of the appliance, which is indicated on the data plate. € the voltage is in the range between the values indicated on the data plate. If the socket is incompatible with the plug, ask an authorised technician to replace it. The internal burner has a nozzle, the external burner has two (of the same size). Replace the nozzle with models suited to the new type of gas (see table 1). Should the gas pressure used be different (or vary slightly) from the recommended pressure, a suitable pressure regulator must be fitted to the inlet pipe (in order to comply with current national regulations). DATA PLATE Electrical see data plate connections ECODESIGN • Adjusting the burners’ primary air Does not require adjusting. Remove the knob and adjust the adjustment screw, which is positioned in or next to the tap pin, until the flame is small but steady. In the event of single-control DRDA (DCDR) burners, adjustment can be performed by intervening on the 2 screws located near the tap pin (see picture). Having adjusted the flame to the required low setting, while the burner is alight, quickly change the position of the knob from minimum to maximum and vice versa several times, checking that the flame does not go out. When using models with an ignition button, light the desired burner pressing down the corresponding knob as far as possible and turning it anticlockwise towards the maximum setting. If a flame is accidentally extinguished, turn off the control knob and wait for at least 1 minute before trying to relight it. To switch off the burner, turn the knob in a clockwise direction until it stops (when reaches the “●” position). Discrete flame adjustment The selected burner can be adjusted - by means of the knob - to 5 different power levels. To shift between levels, simply turn the knob towards the desired power level. The selected power level is indicated by the corresponding symbol (symbols ) and, on hobs equipped with a display, by the LEDs that turn on (5 = max. [. . . ] Old appliances must be collected separately in order to optimise the recovery and recycling of the materials they contain and reduce the impact on human health and the environment. The crossed out “wheeled bin” symbol on the product reminds you of your obligation, that when you dispose of the appliance it must be separately collected. Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliance. € Clean the enamelled and glass parts only with soft cloth or sponge. [. . . ]