User manual HOTPOINT PCN 751 T/IX/A

[. . . ] PCN 641 N/T/IX/A PCN 641 T/IX/A PCN 642 IX/A PCN 751 T/IX/A Español Manual de instrucciones ENCIMERA Sumario Manual de instrucciones, 1 Advertencias, 3 Asistencia, 5 Descripción del aparato, 6 Instalación, 20 Puesta en funcionamiento y uso, 24 Precauciones y consejos, 24 Mantenimiento y cuidados, 25 Anomalías y soluciones, 25 English Portuges Operating Instructions HOB Contents Operating Instructions, 1 Warnings, 2 Assistance, 5 Description of the appliance, 6 Installation, 8 Start-up and use, 12 Precautions and tips, 12 Maintenance and care, 13 Troubleshooting, 13 Instruções para a utilização PLANO Índice Instruções para a utilização, 1 Advertências, 3 Assistência, 5 Descrição do aparelho, 6 Instalação, 26 Início e utilização, 30 Precauções e conselhos, 30 Manutenção e cuidados, 31 Anomalias e soluções, 31 Français Mode d’emploi TABLE DE CUISSON Sommaire Mode d’emploi, 1 Avertissements, 2 Assistance, 5 Description de l’appareil, 6 Installation, 14 Mise en marche et utilisation, 18 Précautions et conseils, 18 Nettoyage et entretien, 19 Anomalies et remèdes, 19 ‫تعليمات التشغيل‬ ‫المحتويات‬ ‫رف تسخين‬ 1،‫تعليمات التشغيل‬ 4،‫تحذيرات‬ 5،‫المساعدة‬ 7،‫وصف الجهاز‬ 33 ،‫التركيب‬ 37،‫بدء التشغيل واالستخدام‬ 37 ،‫وسائل الحذر والنصائح‬ 37 ،‫الصيانة والعناية‬ 36 ،‫استكشاف المشاكل وحلها‬ Warnings WARNING: The appliance and its accessible parts become hot during use. Children less than 8 years of age shall be kept away unless continuously supervised. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Cleaning and user maintenance shall not be made by children without supervision. [. . . ] These pipes must be installed so that they are never longer than 2000 mm when fully extended. Once connection has been carried out, make sure that the flexible metal pipe does not touch any moving parts and is not compressed. Only use pipes and seals that comply with current national regulations. When the installation process is complete, check the pipe fittings for leaks using a soapy solution. Adapting to different types of gas To adapt the hob to a different type of gas other than default type (indicated on the rating plate at the base of the hob or on the packaging), the burner nozzles should be replaced as follows: 1. Unscrew the nozzles using a 7 mm socket spanner, and replace them with nozzles for the new type of gas (see table 1 “Burner and nozzle characteristics”). Reassemble the parts following the above procedure in the reverse order. Once this procedure is finished, replace the old rating sticker with one indicating the new type of gas used. Replace the nozzles with models that are configured for use with the new type of gas (see Table 1). Electrical connection Hobs equipped with a three-pole power supply cable are designed to operate with alternating current at the voltage and frequency indicated on the data plate (this is located on the lower part of the appliance). If the appliance is to be installed above a built-in electric oven, the electrical connection of the hob and the oven must be carried out separately, both for electrical safety purposes and to make extracting the oven easier. Connecting the supply cable to the mains Install a standardised plug corresponding to the load indicated on the data plate. The appliance must be directly connected to the mains using an omnipolar circuit-breaker with a minimum contact opening of 3 mm installed between the appliance and the mains. The circuit-breaker must be suitable for the charge indicated and must comply with current electrical regulations (the earthing wire must not be interrupted by the circuit-breaker). The supply cable must not come into contact with surfaces with temperatures higher than 50°C. The installer must ensure that the correct electrical connection has been made and that it is compliant with safety regulations. Before connecting to the power supply, make sure that: • the appliance is earthed and the plug is compliant with the law. € the socket can withstand the maximum power of the appliance, which is indicated on the data plate. Gas burners Each burner can be adjusted to one of the following settings using the corresponding control knob: ● Off Maximum Minimum To light one of the burners, hold a lit match or lighter near the burner and, at the same time, press down and turn the corresponding knob anti-clockwise to the maximum setting. Since the burner is fitted with a safety device, the knob should be pressed for approximately 2-3 seconds to allow the automatic device keeping the flame alight to heat up. When using models with an ignition button, light the desired burner pressing down the corresponding knob as far as possible and turning it anticlockwise towards the maximum setting. If a flame is accidentally extinguished, turn off the control knob and wait for at least 1 minute before trying to relight it. [. . . ] First, check to see that there are no interruptions in the gas and electrical supplies, and, in particular, that the gas valves for the mains are open. € All the movable parts that make up the burner are mounted correctly. € You keep the knob pressed in long enough to activate the safety device. € The gas holes are not blocked in the area corresponding to the safety device. [. . . ]