User manual HOTPOINT NMTP 1922 FW/HA

[. . . ] 01 04/2008 I 12 Operating Instructions 2-DOOR FRIDGE Contents I Italiano, 1 GB GB English, 13 F Français, 25 Installation, 14 Positioning and connection Reversible doors Description of the appliance, 15-16 Control panel Overall view ES Espanol, 1 Accessories, 17 Refrigerator compartment Freezer compartment Start-up and use, 18-19 NMTP 1922 FW/HA NMTP 1923 FW/HA Starting the appliance Using the display Chiller system Using the refrigerator to its full potential Using the freezer to its full potential Maintenance and care, 20 Switching the appliance off Cleaning the appliance Avoiding mould and unpleasant odours Replacing the light bulb Precautions and tips, 21 General safety Disposal Respecting and conserving the environment Troubleshooting, 22 Assistance, 23 13 Installation GB !Before operating your new appliance please read these instructions carefully. They contain important information for safe use, installation and care of the appliance. Electrical connections After transportation of the appliance, carefully place it in an upright position and wait at least 3 hours before connecting it to the electricity mains. [. . . ] This flashing and sound signal indicates that the function is complete and that the bottle should be removed from the freezer compartment. Child Lock In order to activate the Child Lock function, the Child Lock button must be pressed for 2 seconds; the activation of the button lock is confirmed by a short beep and the illumination of the corresponding LED. To deactivate the function, press the Child Lock button for 2 seconds; deactivation will be confirmed by a short beep and by the corresponding LED switching off. The FREEZER status bar is also used to indicate Navigating the display Setting the temperatures: If the product is switched on, the refrigerator and freezer status bars will indicate the temperatures set at that and moment. To change them, simply press the buttons corresponding to the compartment for which you wish to change the set temperature. More specifically, each time one of the buttons is pressed the temperature is increased or decreased by 1°, and the level of cold is adjusted accordingly. The temperature values that may be selected for the refrigerator compartment are +12°C, +7°C, +6°C, +5°C, +4°C, +3°C and +2°C, while the values that may be set for the freezer are -18°C, -19°C, 120°C, -21°C, -22°C, -24°C and -26°C. an unusual temperature increase in the freezer compartment (see Troubleshooting). 18 Chiller system No Frost The No Frost system circulates cold air continuously to collect humidity and prevent ice and frost formation. The system maintains an optimal humidity level in the compartment, preserving the original quality of the food, preventing the food from sticking together and making defrosting a thing of the past. Do not block the aeration cells by placing food or containers in direct contact with the refrigerating back panel. Using the freezer to its full potential • Adjust the temperature using the display. • To freeze (if the freezer is already operating): - for small quantities which are less than those indicated on the data plate, press the rapid freezing SUPER FREEZE button (corresponding indicator light illuminates), insert the food and close the door. The function is disabled automatically after 24 hours or when optimal temperatures have been reached (indicator light goes out); - for large quantities which are greater than the maximum load indicated on the data plate, hold down the rapid freezing SUPER FREEZE button until the corresponding indicator light begins to flash. After 24 hours the indicator light stops flashing and remains on constantly. After another 24 hours, the function will be disabled automatically (indicator light goes out). • Do not re-freeze food that is defrosting or that has already been defrosted. • Fresh food that needs to be frozen must not come into contact with food that has already been defrosted. Access the light bulb as shown (see diagram) and replace it with a similar light bulb, the power of which should not exceed 10 W. Cleaning the appliance • The external and internal parts and the rubber seals may be cleaned using a sponge that has been soaked in lukewarm water and bicarbonate of soda or neutral soap. This can be removed by carefully using the hose of a vacuum cleaner set on medium power. The appliance must be switched off and the plug disconnected from the electricity mains before it is cleaned. [. . . ] The alarm sounds, the ALARM LED lights up and the freezer status bar LEDs light up in sequence. Possible causes / Solutions: • The plug has not been inserted into the electrical socket, or not far enough to make contact, or there is no power in the house. The appliance comes with a motor protection control (see Start-up and use). • Pull out and reverse the plug before putting it back in the socket. [. . . ]