User manual HOTPOINT HLQB 9.8 LASI X/HA

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual HOTPOINT HLQB 9.8 LASI X/HA. We hope that this HOTPOINT HLQB 9.8 LASI X/HA user guide will be useful to you.


HOTPOINT HLQB 9.8 LASI X/HA : Download the complete user guide (7613 Ko)

You may also download the following manuals related to this product:

   HOTPOINT HLQB 9.8 LASI X/HA (6122 ko)

Manual abstract: user guide HOTPOINT HLQB 9.8 LASI X/HA

Detailed instructions for use are in the User's Guide.

[. . . ] € NEVER cook food with an open flame under the hood; open flames will damage the filters and may cause fires. € Always supervise frying to make sure the heated oil does not catch fire. € Strictly observe all local regulations in relation to the technical and safety measures to be employed in fumes extraction. € Clean the product frequently, inside and out (AT LEAST ONCE A MONTH, and in observance of the maintenance instruction given in this manual). [. . . ] This version requires an air deflector, a reduction adapter and the charcoal filter/s. Electrical hook up The mains voltage must match that given on the ratings label inside the hood itself. If the hood has a power plug, connect the hood to an easily accessible regulatory power socket. If it does not (direct connection to the mains), or the socket is not easily accessible, install a two-pole regulatory switch to enable total disconnection from the mains in case of category III overvoltage, as required by the installation regulations. Always check that the mains cable is hooked up properly and check that it operates correctly before reconnecting the hood to the mains. Air exhaust (for ducted units) Connect the hood to a duct and wall exhaust hole of a diameter equal to that of the air outlet flange. Using a smaller diameter tube and exhaust hole reduces the extraction capacity of the hood and also increases its running noise. Do not connect the hood to flues carrying combustion fumes from other equipment (boilers, TBOX-GLASSs, stoves, etc. Observe the instructions of the competent authorities in relation to the air exhaust. The air being exhausted may not be exhausted into a wall cavity unless the cavity in question is specifically intended for this purpose. The time for cleaning/replacement is signalled by the flashing of the coloured LED associated to the filter (white for antigrease filters, red for odour filter). The LED is turned off by pressing the T7 button after cleaning/replacing the filters. Hood configuration The configuration menu is accessed with the product off by pressing T5 and T6 for 6 seconds. T7 turns on at this point to indicate the type of installation through two colours of the LED: white for extractor installation (default), red for filtering installation. The installation type can be changed by pressing T7 cyclically with the consequent alternation of the LED colours. T1 T2 T3 T4 T5 T6 T1 motor ON/OFF When the button is pressed with the hood off, the first speed is set. T2 Speed – When the button is pressed the hood switches to the previous speed. T3 Speed + If the hood is set to speed 3, the intensive speed activates when this button is pressed The setting is limited by time; when it elapses the hood goes back to the speed set previously. T4 Timer “–” Set a time to turn OFF the hood with the timer; if the timer is set and the speed is subsequently changed by pressing T2, T3 or T4, the timer is deactivated. T5 Timer “+” When the button is pressed for the first time, the timer is set to 5 minutes; this value is increased by 5 additional minutes every time the button is pressed after that. [. . . ] This filter can NOT be washed or regenerated Disassembly: Remove the activated-carbon filter by B pressing the two front levers which secure it to the hood. Before cleaning or servicing the unit, disconnect it from the mains by pulling the power plug or disconnecting the main circuit breaker. First cleaning • Remove the protective film • Clean with a damp sponge and a little neutral soap • Rinse off with a damp cloth • Dry with a soft cloth; if the hood is stainless steel, dry along the metal's grain Periodic cleaning The hood must be cleaned frequently (at least as often as you service the grease filter), inside and out. Warning: Failure to observe the hood cleaning and filter cleaning/replacement instructions can result in fires. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE HOTPOINT HLQB 9.8 LASI X/HA




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual HOTPOINT HLQB 9.8 LASI X/HA will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.