User manual HOTPOINT HKID641B C

[. . . ] Indicates a hazardous situation which, if not avoided, could cause serious injury. All messages relevant to safety specify the potential risk to which they refer and indicate how to reduce the risk of injury, damage and electric shocks due to incorrect use of the appliance. Make sure to comply with the following: - Use protective gloves to perform all unpacking and installation operations. - The appliance must be disconnected from the power supply before carrying out any installation operation. [. . . ] Sauces, soups, minestrone) Ideal for keeping just-cooked food hot, creaming risottos and keeping serving dishes warm (with induction-suitable accessory), Hob in standby mode or off (possible end-of-cooking residual heat, indicated by “H”) Max. Power Medium power 4-3 Low power 2-1 Zero power OFF NOTE: When making quick-cook foods that require perfect heat distribution (e. Pancakes) on the 28 cm double cooking zone (where present), use pans no greater than 24 cm in diameter. For delicate cooking (for example, melting chocolate or butter) use the smaller diameter single zones. INSTALLATION After unpacking the product, check for any damage during transport. For built-in dimensions and installation instruction, see the pictures in page 2. pREPARING THE CABINET FOR FITTING WARNING • • • • • Install a separator panel under the hob. The lower part of the product must not be accessible after installation. 20 mm 6-7 cm The distance between the underside of the appliance and the separator panel must respect the dimensions given in the figure. In order to ensure the correct operation of the product, do not obstruct the minimum required clearance between the hob and the top of the unit (min. If an undertop oven is installed, make sure the oven is equipped with a cooling system. In these situations it is recommended to reposition the pot on the hob surface until you find the position of operation. Fast boil function (Booster where it is available) This function, only present on some cooking zones, makes it possible to exploit the hob’s maximum power (for example to bring water to the boil very quickly). To activate the function, press the “+” button until “P” appears on the display. After 5 minutes’ use of the booster function, the appliance automatically sets the zone to level 9. FLEXI This function is used in case of big pots that the single zone can not satisfied, ex, fish, big pot for meat. In order to active the FLEXI/CONNEXTION ZONE, please press on + and - buttons simultaneously as shown in the picture below. €Power management” (Function where it is available) Thanks to the “Power management” function, the user can set the maximum power the hob can reach, as required. This setting is possible at any time and is maintained until the next change. By setting the required maximum power, the hob automatically adjusts distribution in the various cooking zones, ensuring that this limit is never exceeded; with the advantage of also being able to manage all the zones simultaneously, but without overload problems. 2 kW is considered as max power of cooktop) At the time of purchase, the hob is set to maximum power After plugging the appliance into the electrical socket, in the first 60 seconds it is possible to set the required power level by running the following points: Step 1 Control panel Display Press for approximately 3 seconds both Power management button (step 1) Press the Power Management button (step 2) to confirm the previous The display shows step Press to set the chosen level The light comes on together with the in-use amongst the different lights for the individual cooking zones options available Press the Power Management button (step 4) to confirm the previous step The display shows the set level which flashes for approximately 2 seconds; after which the hob emits an acoustic signal and then turns itself off; it is now ready for use 2 3 4 In case of an error when setting the power, the symbol appears in the middle and an acoustic signal sounds for about 5 seconds. During normal use, if the user tries to increase the maximum available power level when reached, the level of the zone in use flashes twice and an acoustic signal sounds. [. . . ] These conditions are normal and essential for the proper functioning of the induction system, they are not indication of failure or damage. eN11 AFTER-SALES SERVICE Before contacting the After-sales Service: 1. See if you can solve the problem yourself with the help of the “Troubleshooting guide”. Switch the appliance off and then on again it to see if the problem has been eliminated. [. . . ]