User manual HOTPOINT H64IL9PAA S

[. . . ] Knapp för INSTÄLLNING AV TID 3 GB Assistance FI Huoltoapu Warning: The appliance is fitted with an automatic diagnostic system which detects any malfunctions. Malfunctions are displayed by messages of the following type: “F” followed by numbers. Please have the following information to hand: • The type of problem encountered. The latter two pieces of information can be found on the data plate located on the appliance. [. . . ] € Crackle: produced by the vibration of materials on the bottom of the pot due to the flow of parasitic currents caused by electromagnetic fields (induction); can be more or less intense depending on the material making up the bottom of the pot, and decreases as the pot dimensions increase. € Loud whistle: heard when two induction elements of the same group function simultaneously at maximum power and/or when the booster function is set on the larger element while the other is auto-adjusted. Noise is reduced by decreasing the power level of the autoadjusted induction element; pot bottom layers made of different kinds of materials are among the main causes of this noise. When power is initially applied to the Cooktop, the touch control conducts a calibration process for the touch keys, which requires a low level of ambient light in the area of the touch keys. If during this calibration process excessive ambient lighting is detected the User Interface displays „FL” (Infrared Ambient Light Error) and the control calibration process is suspended. In order to rectify the process any lighting that could effect the calibration process should be switched off (e. The error will disappear when satisfactory ambient lighting is detected and the touch control calibration procedure will now complete satisfactorily. -The „FL” error can only be generated within approx 3s of initial power being applied to the cooktop. -We recommend that the user switches off all cooker hood lighting and lighting directed towards the cooktop when power is initially applied to the cooktop. -After the touch control has conducted its initial calibration process, (approx 3s) any cooker hood or other lighting can be switched on as normal and will not affect the operation of the touch control. Switching on the hob After connecting the hob to the electrical grid, the touch pannel might be automatically locked. Button for To switch the hob on, press and hold the approximately one second. The cooktop is switched On when a beep sound is emitted and the cooking zones display shows the „0” 17 GB When the cooktop is off, after 5 sec. Without any error/ alarm or residual heat to display, the control switches Switching off the cooking zones To switch off a cooking zone touch(-)and (+) POWER selection buttons simultaneously. A beep sounds, the timer display shows a “00” and the cooking zone displays show a “t” blinking indicating that a cooking zone has to be selected. 2 Select the desired cooking zone by pressing any of the cooking zones (+) or (-)keys. A beep sounds, the LED next to the cooking zone display starts blinking if no power is selected, or is on if any power is selected. The timer display starts blinking indicating that the time has to be selected 3. Pressing and holding the (+) and (-) keys increases the speed of time selection. If the time is not selected before 10 seconds, the timer is switched off. If the selected time is “00” after 10 seconds the timer is switched off. Using the Timer Fast Boil- “Booster” function The booster function for some of the cooking zones may be used to shorten heating-up times. [. . . ] Glass ceramic hob cleaners Window scraper Razor blade scrapers Available from DIY Stores DIY Stores, supermarkets, chemists Boots, Co-op stores, department stores, Regional Electricity Company shops, supermarkets Replacement blades COLLO luneta HOB BRITE Hob Clean SWISSCLEANER Replacing the oven light bulb To replace the oven light bulb: 1. Unscrew the light bulb and replace it Cavity with a similar one: Wattage 15 W, cap Light bulb E 14. Replace the glass Seal cover, making sure the seal is Cover positioned correctly (see diagram). 23 GB Automatic cleaning using the PYROLYTIC cycle During the PYROLYTIC cycle, the internal temperature of the oven reaches 500°C. [. . . ]