User manual HOTPOINT FTGHG 751 D/HA

[. . . ] мұны Пайдалану нұсқаулығы, 1 Ескертулер, 3 Көмек, 4 Құрылғы сипаттамасы, 6 Орнату, 21 Қосу және пайдалану, 25 Сақтандырулар мен кеңестер, 25 Жөндеу және күтім, 26 Ақаулықтарды жою, 26 English Operating Instructions HOB Contents Operating Instructions, 1 Warnings, 2 Assistance, 4 Description of the appliance, 5 Installation, 7 Start-up and use, 10 Precautions and tips, 10 Maintenance and care, 11 Troubleshooting, 11 Русскии Руководство по эксплуатации ВАРОЧНАЯ ПАНЕЛЬ Содержание Руководство по эксплуатации, 1 Предупреждения, 2 Сервисное обслуживание, 4 Описание из делия, 5 Установка, 13 Включение и эксплуатация, 17 Предосторожности и рекомендации, 17 Техническое обслуживание и уход, 18 Неисправности и методы их устранения, 19 Warnings WARNING: The appliance and its accessible parts become hot during use. Children less than 8 years of age shall be kept away unless continuously supervised. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Cleaning and user maintenance shall not be made by children without supervision. [. . . ] Connection to the gas system must be carried out in such a way as not to place any strain of any kind on the appliance. There is an adjustable L-shaped pipe fitting on the appliance supply ramp and this is fitted with a seal in order to prevent leaks. The seal must always be replaced after rotating the pipe fitting (seal provided with appliance). These pipes must be installed so that they are never longer than 2000 mm when fully extended. Once connection has been carried out, make sure that the flexible metal pipe does not touch any moving parts and is not compressed. Only use pipes and seals that comply with current national regulations. When the installation process is complete, check the pipe fittings for leaks using a soapy solution. Should the gas pressure used be different (or vary slightly) from the recommended pressure, a suitable pressure regulator must be fitted to the inlet pipe (in order to comply with current national regulations). DATA PLATE Electrical see data plate connections This appliance conforms to the following European Economic Community directives: - 2006/95/EC dated 12/12/06 (Low Voltage) and subsequent amendments - 2004/108/EC dated 15/12/04 (Electromagnetic Compatibility) and subsequent amendments - 93/68/EEC dated 22/07/93 and subsequent amendments. The hob can only be installed above built-in ovens with a cooling ventilation system. Electrical connection Hobs equipped with a three-pole power supply cable are designed to operate with alternating current at the voltage and frequency indicated on the data plate (this is located on the lower part of the appliance). If the appliance is to be installed above a built-in electric oven, the electrical connection of the hob and the oven must be carried out separately, both for electrical safety purposes and to make extracting the oven easier. Connecting the supply cable to the mains Install a standardised plug corresponding to the load indicated on the data plate. The appliance must be directly connected to the mains using an omnipolar circuit-breaker with a minimum contact opening of 3 mm installed between the appliance and the mains. The circuit-breaker must be suitable for the charge indicated and must comply with current electrical regulations (the earthing wire must not be interrupted by the circuit-breaker). The supply cable must not come into contact with surfaces with temperatures higher than 50°C. The installer must ensure that the correct electrical connection has been made and that it is compliant with safety regulations. Before connecting to the power supply, make sure that: • the appliance is earthed and the plug is compliant with the law. € the socket can withstand the maximum power of the appliance, which is indicated on the data plate. € the voltage is in the range between the values indicated on the data plate. If the socket is incompatible with the plug, ask an authorised technician to replace it. Once the appliance has been installed, the power supply cable and the electrical socket must be easily accessible. [. . . ] € Models equipped with electrical ignition plugs and safety device require thorough cleaning of the plug end in order to ensure correct operation. Check these items frequently, and if necessary, clean them with a damp cloth. To avoid damaging the electric ignition device, do not use it when the burners are not in their housing. GB Gas tap maintenance Over time, the taps may become jammed or difficult to turn. [. . . ]