User manual HOTPOINT FC 98 P.1 IX

[. . . ] IT 26 Congratulations on choosing an Ariston appliance, which you will find is dependable and easy to use. We recommend that you read the instructions in this owner's manual carefully before use for the best performance and to extend the life of your appliance, as it will provide you with all the instructions you require to ensure its safe installation, use and maintenance. Always keep this owner's manual close to hand since you may need to refer to it in the future. Control Panel Cooking mode selection knob Cooking temperature / time selection knob Electronic programmer Dripping Pan or Baking Sheet Oven Rack Guides for sliding the racks or dripping pan in and out 1. [. . . ] Use a specific non-abrasive product to remove tougher stains, Using aluminium foil To avoid having to clean the bottom of the oven, you may be tempted to line the same with some aluminium foil. The aluminium foil sheet in direct contact with the heated enamel coating could melt and damage the enamel coating inside the oven irreversibly. Cleaning the rotisserie and other accessories The rotisserie can be removed completely thanks to the 2 wing nuts. The elements comprising the rotisserie assembly should be cleaned together with the other accessories (dripping pan, grid) in the sink using a damp sponge and ordinary detergent or even in your dishwasher. FC 98 P 1 2 3 Replacing the oven lamp • Always unplug the appliance from the mains or switch off the main switch before all operations. € With the aid of a narrow, flat item (such as a screwdriver or a spoon handle, etc…), remove the glass cover. € Unscrew the lamp and replace it with another featuring the same characteristics: - voltage 230/240 W - wattage 15 W - type E 14 • Replace the glass cover and ensure you reposition the seal correctly. Disassembling the oven door The oven door can easily be removed to clean the space between the bottom of the door and the front of the oven. To disassemble the door, proceed as follows: • open the oven door fully, • lift up and turn the small levers situated on the two hinges, • shut the door, but not completely, • grip the door on the two external sides and pull it towards you, pulling it out of its seat. FO / FD 98 P 1 2 3 Oven compartment Lamp Seal Glass door 31 GB Fast clean Safety devices In fast clean mode, the temperature inside the oven reaches 500°, which is necessary for the destruction of food and fat residue, as illustrated below. Given this high temperature, your oven is fitted with some safety devices: • the oven door is locked automatically as soon as the temperature is high in order to avoid all risks of burns. Note: When looking through the oven door, you may notice some particles that light up when they are destroyed by pyrolysis upon contact with the heating elements: this is simply spontaneous combustion, it is extremely normal and without danger. • Turn knob B and set it to FAST CLEAN • The cleaning process takes approximately 90 minutes. You can set the duration of the cleaning cycle (60 - 90 - 120 minutes) depending on the degree of soil of your oven. Just as for cooking, you can set a fast clean cycle with a delayed start. ð The oven door is locked automatically as soon as you start a fast clean cycle. ð The key indicator light flashes while the door is being locked and the cycle time gradually decreases. The indicator light stops flashing and stays on as soon as the oven door is locked. Precautions to be taken before performing the fast clean process 1- Try to remove the larger food residue from inside the oven using a wet sponge. We highly advise against the use of detergents or all other products recommended for cleaning ovens. 2- Remove all the accessories from the oven: they are not designed to withstand such high temperatures. What's more, some of these accessories would alter the result of the pyrolytic self-cleaning process and obstruct the circulation of heat inside the oven. [. . . ] All parts which ensure the safe operation of the appliance must be removable only with the aid of a tool. For the correct centring of your appliance, position the 4 tabs on the sides of the oven in correspondence with the 4 holes on the perimeter of the frame. In particular, if the cabinet side panel: • is 20 mm thick: the removable part of the tab must be removed (Fig. A); • is 18 mm thick: use the first groove, which is factoryset (Fig. [. . . ]