User manual HOTPOINT EHP 640 (X)/HA

[. . . ] EHP 640 (X) /HA Français Mode d’emploi TABLE DE CUISSON Sommaire Mode d’emploi, 1 Avertissements, 3 Assistance, 4 Description de l’appareil, 5 Installation, 18 Mise en marche et utilisation, 23 Précautions et conseils, 23 Nettoyage et entretien, 24 Anomalies et remèdes, 24 Italiano Istruzioni per l’uso PIANO Sommario Istruzioni per l’uso, 1 Avvertenze, 2 Assistenza, 4 Descrizione dell’apparecchio, 5 Installazione, 6 Avvio e utilizzo, 10 Precauzioni e consigli, 10 Manutenzione e cura, 11 Anomalie e rimedi, 11 English Operating Instructions HOB Contents Operating Instructions, 1 Warnings, 2 Assistance, 4 Description of the appliance, 5 Installation, 12 Start-up and use, 16 Precautions and tips, 16 Maintenance and care, 17 Troubleshooting, 17 Avvertenze ATTENZIONE: Questo apparecchio e le sue parti accessibili diventano molto caldi durante l’uso. Warnings WARNING: The appliance and its accessible parts become hot during use. Children less than 8 years of age shall be kept away unless continuously supervised. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. [. . . ] If this is not the case, follow the instructions indicated in the paragraph “Adapting to different types of gas. € When using liquid gas from a cylinder, install a pressure regulator which complies with current national regulations. Check that the pressure of the gas supply is consistent with the values indicated in Table 1 (“Burner and nozzle specifications”). This will ensure the safe operation and longevity of your appliance while maintaining efficient energy consumption. Connection to the gas system must be carried out in such a way as not to place any strain of any kind on the appliance. There is an adjustable L-shaped pipe fitting on the appliance supply ramp and this is fitted with a seal in order to prevent leaks. The seal must always be replaced after rotating the pipe fitting (seal provided with appliance). These pipes must be installed so that they are never longer than 2000 mm when fully extended. Once connection has been carried out, make sure that the flexible metal pipe does not touch any moving parts and is not compressed. Only use pipes and seals that comply with current national regulations. When the installation process is complete, check the pipe fittings for leaks using a soapy solution. Adapting to different types of gas To adapt the hob to a different type of gas other than default type (indicated on the rating plate at the base of the hob or on the packaging), the burner nozzles should be replaced as follows: 1. Unscrew the nozzles using a 7 mm socket spanner, and replace them with nozzles for the new type of gas (see table 1 “Burner and nozzle characteristics”). Reassemble the parts following the above procedure in the reverse order. Once this procedure is finished, replace the old rating sticker with one indicating the new type of gas used. € Adjusting the burners’ primary air Electrical connection Hobs equipped with a three-pole power supply cable are designed to operate with alternating current at the voltage and frequency indicated on the data plate (this is located on the lower part of the appliance). If the appliance is to be installed above a built-in electric oven, the electrical connection of the hob and the oven must be carried out separately, both for electrical safety purposes and to make extracting the oven easier. Connecting the supply cable to the mains Install a standardised plug corresponding to the load indicated on the data plate. The appliance must be directly connected to the mains using an omnipolar circuit-breaker with a minimum contact opening of 3 mm installed between the appliance and the mains. The circuit-breaker must be suitable for the charge indicated and must comply with current electrical regulations (the earthing wire must not be interrupted by the circuit-breaker). The supply cable must not come into contact with surfaces with temperatures higher than 50°C. The installer must ensure that the correct electrical connection has been made and that it is compliant with safety regulations. [. . . ] This appliance has been designed and manufactured in compliance with international safety standards. The following warnings are provided for safety reasons and must be read carefully. € When disposing of packaging material: observe local legislation so that the packaging may be reused. € The European Directive 2012/19/EC on Waste Electrical and Electronic Equipment (WEEE), requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. [. . . ]