User manual HOTPOINT-ARISTON TCDG51

[. . . ] Si l’affichage n’est pas allumé : appuyez sur le bouton MARCHE/ARRET Appuyez sur le bouton de sélection de programme qui correspond au type de tissu que l’on sèche ; après avoir vérifie le Tableau des Programmes (voir Programmes) ainsi que les indications pour chaque type de tissu (voir Linge). Cet appareil est conforme aux Directives Européennes suivantes: - 2006/95/EC (Équipement Basse Tension) - 89/336/EEC, 92/31/EEC et 93/68/EEC (Compatibilité Électromagnétique) 17 18 Instruction booklet TUMBLE DRYER F Français, 1 GB English, 19 Contents Important information, 20-21 Installation, 22 Where to put your dryer Ventilation Electrical connection Before you start using your dryer GB Dryer description, 23 To open the door The features Control panel The Display, 24-26 Start and programmes, 26-29 Choosing a programme Special programmes Programme option modifiers Table of programmes The controls TCD G51 First time you turn on your dryer you must select your preferred language see page 24 Laundry, 30-31 Sorting your laundry Wash care labels Special clothing items Drying times Warnings and Suggestions, 32 General safety Disposal Saving energy and respecting the environment Maintenance and Care, 33 Switching off the electricity Cleaning the filter after each cycle Empty the water container after each cycle Check the drum after each cycle Cleaning the condenser unit Cleaning the dryer Troubleshooting, 34 Service, 35 Spare parts !Keep this instruction booklet on hand in order to refer to it when necessary. Take it with you when you move, and should you sell this appliance or pass it on to another party, make sure that this booklet is supplied along with the dryer so that the new owner may be informed about warnings and suggestions on how the appliance works. [. . . ] (0:20, 0:30, 0:30 , 1:00 , 1:30 , 2:00 , 2:40 , 3:00 then 1:00, 1:30, 2:00, and then repeats. The heat setting depends q 2:40 or 3:00 Delicates have maximum time of 1:40 . on the programme Hours:Minutes) GB (material option) selected. Q When is displayed, Automatic option is available if you change your mind. Warning, after pressing the Start/Pause button , the programme cannot be changed. To change a selected programme, press the Start/Pause button , the light flashes Amber to indicate the programme is paused. Select the new programme and any options required, the light will then flash green. Q Option buttons / icons These buttons are used to customise the selected programme to your requirements. A programme must have been selected, by pressing a programme selection button, before an option can be selected. Not all options are available for all programmes (see Programmes Table). If an option is not available and you press the button, the buzzer will beep 3 times. If the option is available the indicator, on the display unit next to the bottom buttons, lights to show that the option has been selected. Time Delay The start of some programmes (see The Display and Start and Programmes) can be delayed for up to 24 hours. pre Care This option is only available if a delayed start has been selected. It tumbles the clothes occasionally during the delayed period to help prevent creases developing. Alarm Available on all programmes and allows the buzzer to give a signal at the end of the drying cycle, to remind you that the clothes are ready to be removed. Post Care When available and selected, the clothes are occasionally tumbled after the end of the drying and cool tumble cycles, to help prevent creases developing should you not be available to remove the load immediately the programme is complete. TIME DISPLAY 88:88 The display shows either the amount of time delay remaining or an indication of the amount of time left for a drying programme (see The Display). The delay or time to end is displayed in hours and minutes and counts down each minute. When timed programmes are selected the time displayed throughout the cycle is the actual time remaining. When an Automatic programme is selected, the time displayed is an estimate of the time remaining. When the programme is selected the display shows the time required to dry a full load, after around 10 minutes the controller calculates a better estimate of the cycle time. [. . . ] Possible causes / Solution: q q q q q q q The plug is not plugged into the socket, or not making contact. The Start/Pause button has not been pressed (see Start and Programmes). The temperature setting is not ideal for the type of fabric you are drying (see Start and Programmes, and see Laundry). The correct drying time has not been selected for the load (see Laundry). [. . . ]