User manual HOTPOINT-ARISTON HBBG05

[. . . ] FP087-01 HP Gas Hob (BG05) 12/09/2001 4:59 pm Page 1 INSTRUCTIONS for INSTALLATION and USE Gas Hob BG05 This appliance must be installed in accordance with regulations in force and only in a well ventilated place. Ensure that the hob unit is securely fixed to the worktop before use. To the Installer Before installation fill in the product details on the back cover of this booklet. To the User You must read the instructions prior to using the appliance and then retain them for future reference. FP087-01 HP Gas Hob (BG05) 12/09/2001 4:59 pm Page 2 CONTENTS Introduction For Your Safety ­ Always For Your Safety ­ Never Using The Hob Care & Cleaning Something Wrong?Installation Hotpoint Service Cover Key contacts 3 4 5 6 7 8 9 - 14 15 Back Cover Retention of this Instruction Book This Instruction Book must be kept handy for reference as it contains important details on the safe and proper use of the appliance. [. . . ] Connection to the electricity supply should be made via a properly earthed, readily accessible wall socket which is adjacent to but not directly above, and not more than 1. 25m away from the appliance and capable of electrical isolation. Should this plug not fit the socket outlet in your home it should be cut off and replaced with a suitable plug as outlined below. NOTE: The removed plug cannot be used for any other appliance and should therefore be properly disposed of and not left where children might find it and plug it into a supply socket ­ with the obvious consequent danger. IF THE FITTED PLUG IS REMOVED The flexible mains lead must be correctly connected as below to a three pin plug of not less than 13 amp capacity. 1363 fused plug is used, it must be fitted with a 3 amp fuse which is approved to B. S. IMPORTANT: The wires in the mains lead fitted to this appliance are coloured in accordance with the following code: GREEN AND YELLOW ­ EARTH BLUE ­ NEUTRAL BROWN ­ LIVE Blue to Neutral Cord Clamp Green & Yellow to Earth Brown to Live 3 Amp Fuse As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:­ The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol or coloured green or green and yellow. The wire which is coloured blue must be connected to the terminal which is marked with the N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. When wiring the plug, ensure that all strands of wire are securely retained in each terminal. As the appliance must be earthed, do not use 2-pin sockets outlets, if you are in doubt, consult a qualified electrician. Should the mains lead ever require replacement, it is essential that this operation be carried out by a qualified electrician and should only be replaced with a flexible cord of the same size i. e. IF A MOULDED PLUG IS FITTED In the event of replacing a fuse in the plug supplied a 3 amp ASTA approved fuse to BS1362 must be fitted. In the event of losing the fuse cover the plug must not be used until a replacement fuse cover has been obtained and fitted. The colour of the correct replacement fuse cover is that of the coloured marks or inserts in the base of the plug. Make sure that the cable does not become trapped. 9 FP087-01 HP Gas Hob (BG05) 12/09/2001 4:59 pm Page 10 INSTALLATION INSTRUCTIONS Gas Category II2H3+ (GB, IE) Model Numbers W810, BG05 These models are set to burn NATURAL GAS (G20) at 20mbar. If the room has a volume between 5 and 10m3, it will require an air vent of 50cm2 effective area unless it has a door which opens directly to outside. If the room has a volume of less than 5m3, it will require an air vent of 100cm2 effective area. If there are other fuel burning appliances in the same room, BS 5440: Part 2 should be consulted to determine air vent requirements. 11 FP087-01 HP Gas Hob (BG05) 12/09/2001 4:59 pm Page 12 INSTALLATION SITING THE HOB The hob is designed to fit into worktop and base unit(s) with a cutout as shown in Fig. 1. Any obstruction such as supports or side panels must be removed to allow 30mm minimum depth below the worktop cutout. Any overhead surface of combustible material must not be closer than 600mm. When installing next to a tall cupboard, partition or wall, for a minimum distance of 400mm above the hotplate a side clearance of at least 40mm should be allowed from the edge of the cutout. This is a type X appliance regarding installation requirements, it is recommended that a shelf is fitted to the cabinet under the hob, but no closer than 10mm to prevent access to the underside of the hob which will become hot when in use. [. . . ] During the first year our Engineer's time and labour is also free. · Our guarantee covers loss of food in our refrigeration and freezer products up to £250 during the first year, subject to verification by one of our engineers. · After the first year we will charge for our Engineer's time and labour. We do, however, operate a range of Service Plans (see opposite) which, for an annual payment, enables you to cover any repair costs which may be necessary. [. . . ]