User manual HOTPOINT-ARISTON HB7861

[. . . ] WARNING: Do not use plug unless fuse holder is in locked position. Changing the Plug Cut off and dispose of the supplied plug if it does not fit your socket. WARNING: To avoid a shock hazard do not insert the discarded plug into a socket anywhere else. Green and yellow (Earth) wire to terminal marked `E', symbol , or coloured green and yellow. IMPORTANT: WIRES IN THE MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE: Green/Yellow Earth Blue Neutral Brown Live If you change the plug, the colour of wires in the mains lead may not correspond with the colour of the markings identifying terminals in the plug. You should therefore wire it as shown (Fig 1). 13A ASTA approved fuse to BS1362. Blue (Neutral) wire to terminal marked `N' or coloured black. Brown (Live) wire to terminal marked `L' or coloured red. Cord clamp Fig 1 Changing the Mains Lead A special lead can be ordered from Hotpoint Service UK: 08709 066 066 or Republic of Ireland: 1850 302 200 If you have damaged the existing lead or require a longer one a charge will be made. It is strongly advised that this work is carried out by a qualified electrician. [. . . ] Connect supplied hoses to appliance water supply, confirm water is flowing before connecting to the appliance inlet valves see `Water Supply' on page 6. Untie drainage hose at rear of appliance and connect to either a standpipe or sink waste drainage system see `Drainage' opposite. Untie mains lead at rear of appliance and plug into electrical supply via a switched socket, see `Electrical Supply' on page 2. Position appliance, taking care not to kink or damage hoses at rear of appliance. Switch on at plug socket. Fig 1 Fig 2 Fig 3 Sink Waste System Note: Ensure the sink outlet pipe has a minimum diameter of 32 mm. Reposition `Hooked End Support' as required along GREY drainage hose. Cut Fig 4 3. If fitting an under sink waste disposal unit (Fig 3), cut out the membrane, bung or blanking plug. Attach the GREY drainage hose to the under sink waste disposal unit securely, using a hose clip (Fig 4). Raise the hose to a minimum height of 800 mm to avoid syphoning. Hose Clip 5. Adjust the Feet. . . This must only be done when the machine is upright. q Release locking rings on the two front feet. q Tighten the locking rings on the front feet. Note: Your appliance may become noisy or move about the floor if it has not been stabilised. Your appliance is now ready to use, refer to `Getting to Know your Appliance' on page 8 to familiarise yourself with the appliance. 10 Step Check List 7 1. q Not available with programme `A' or the wool programme `K'. Note: Remember to cancel selections after use. Automatic Features Pulse Spin (for Models WM80, WM79, WM77, WM68, WM67, WM66 & WM60 only) Helps reduce wear and tear on your wash items. Pulse spin is an automatic function where a long steady spin is followed by a 30 second burst at the maximum speed of your appliance to enable safer, more efficient water extraction. Intelligent Care Your appliance has an inbuilt feature to prevent it spinning with an unbalanced load, avoiding excessive vibration and prolonging the life of the appliance. 12 Weight of Wash Load Two examples of typical wash loads for different types of fabric Washcare Tips Before washing laundry:- q Pre-treat stains. COTTON 2 Bath Towels 5 Shirts 6 Blouses 1 Set of Pyjamas 4 Sets of Underwear q Close zips, tie belts, strings etc. . . q Remove sharp objects or coins from pockets as they may damage clothes. q Limit size of absorbent loads ie. ; towels, to 3kg (7lb) to give good washing/rinsing results. q Wash non-colour fast items, woollens or really dirty clothes separately as they may affect other items. q Laundry without a wash label should not be machine washed. = 5. 5kg SYNTHETIC 2 Children's Dresses 4 Shirts 4 Blouses 1 Set of Pyjamas 4 Sets of Underwear = 3kg Spin only options IMPORTANT INFORMATION: Before selecting a programme, ensure the mains button is in the `OFF' position. To select long spin, turn wash dial clockwise until pointer aligns with (Fig 1). For a short spin turn wash dial and align pointer to (Fig 2). Fig 1 Fig 2 Press the mains button `ON'. 13 IMPORTANT INFORMATION: The Main Wash Indicator has been preset to dispense powder detergent only. If you wish to dispense liquid detergent see instructions for `Changing the Main Wash Indicator' opposite. The Dispenser Drawer 1 2 3 4 5 6 Index 1. Liquid or powder detergent compartment (pre-set to dispense powder only). [. . . ] Remember you may be charged for a service call if a problem with your appliance is caused by incorrect installation or misuse. It's Leaking. . . q q Are the fill hoses tightened correctly?You will need to call a plumber if you cannot clear the blockage. The door release button is stuck. . . Switch `OFF' the mains on/off button and apply light pressure to the door to release. The dispenser drawer will not close properly. . . q Is the drawer clogged with detergent?See `Cleaning' section. My appliance will not dispense detergent. . . Have you selected the wash programme correctly?Failure to correctly align pointer at the start of the wash programme will result in the detergent not being dispensed. [. . . ]