User manual HOTPOINT-ARISTON HB6220

[. . . ] 1/2 Temperature & pressure relief valve, 3/4 NPT male COMPONENT PARTS OF GL 8Ti (Horizontal installation) Hot water outlet 3/4 NPT male 3/4 NPT male plug 3/4 NPT female tapping for relief valve Temperature & pressure relief valve discharge line to drain Cold water inlet 3/4 NPT male 3/4 NPT female tapping FIG. 1/3 Hot water outlet 3/4 NPT male Temperature & pressure relief valve, 3/4 NPT male Cold water inlet 3/4 NPT male COMPONENT PARTS OF GL 8Ti (Vertical installation) 3/4 NPT female tapping for relief valve Temperature & pressure relief valve discharge line to drain 3/4 NPT male plug 3/4 NPT female tapping 2 FIG. 2/1 14" 3 3/4" DIMENSIONS FOR GL 2. 5Ti - GL 4Ti 10 1/4" 6" 1/2 NPT MALE 3 1/2" 12 1/4" GL 2. 5 7 1/2" 3" 1" 5 1/2" 2 1/2" 14" GL 4 FIG. 2/2 DIMENSIONS FOR GL 8Ti (HORIZONTAL INSTALLATION) 14 1/2" 8 1/2" 4 1/2" 3/4 NPT MALE 17 1/2" 17 1/2" 14 1/2" 8 1/2" 4 1/2" 1" 17 1/2" 3" 11 1/2" FIG. [. . . ] 3/2) and connect wiring to right side of thermostat control and ground. When the GL8Ti is not within sight of the electrical circuit breakers, a circuit breaker lockout or additional local means of disconnection for all non grounded conductors must be provided that is within sight of the appliance. [REF NEC 422. 31] Connect the cold water inlet pipe to the inlet nipple (marked with a blue ring) and the hot water outlet pipe to the outlet nipple (marked with a red ring). The model GL8Ti can be piped horizontally from the side or vertically from the top. If you wish to install the unit horizontally, with the piping connections on the right side, you will have to be certain the tap between the two water tappings is plugged, the supplied Temperature and Pressure Relief Valve will need to be installed on top. 2/2. Pipe connections 4 If you wish to install the unit vertically, with the piping connections on top, you will have to be certain the tap on the side is plugged, the supplied Temperature and Pressure Relief Valve will need to be installed on top. 3/2 Z F G H E X Y T A MODEL GL 2. 5Ti - GL 4Ti The GL 2. 5Ti and GL 4Ti water heaters can be installed under the sink. Use screws that are suitable for the wall material and the weight of the heater. Tug down wards on the heater to ensure that both "fingers" of the bracket are seated in the mounting slots. 5 Floor Mounting Pipe connections CAUTION Heater can sit on floor. Connect the cold water inlet pipe to the inlet nipple (marked with a blue ring) and the hot water outlet pipe to the outlet nipple (marked with a red ring). 4 B D Maintenance instructions Note: Do not attempt to repair this water heater yourself. Always turn off the power supply to the heater prior to servicing or draining the heater. Periodic maintenance Note: For most of these operations, the water will have to be drained from the heater. For all of these operations the power supply needs to be shut off and the front cover removed. When reassembling, work in the opposite way being careful to insert the tongue of the cover into the slot. Draining the Heater 1) If the heater has been installed with flexible hoses, shut off the power supply and turn the heater upside down over a sink to drain the water out of it, OR 2) If the heater has been installed with rigid piping, siphon the water out through any (lower) service valve on the (inlet side). Keep a hot water faucet open while siphoning the water out, OR 3) If the heater has been installed with flexible hoses, it can also be emptied by siphoning through the inlet side hose. Keep a hot water faucet open while siphoning. 7 Removing the heating element 1. 5/2 Descaling the heating element Scale deposits can affect the heating capability of the element. The element can be descaled either chemically or manually: A) Soak the element in white vinegar or other descaling solution. Once descaled, rinse well with fresh water, to which you should add some baking soda, OR B) Once the element has dried up, use a soft brush (non metallic to prevent damaging the stainless steel sheath) on element. When reassembling, work in the opposite way being careful to insert the tongue of the cover into the slot. IMPORTANT: Check the operation of the thermostat, turn temperature dial from high to low, if the red light does not go off on low setting, turn off power supply and call a service person to replace the thermostat. [. . . ] The Manufacturer shall not be liable for any water damage arising, directly or indirectly, from any defect in the water heater component part(s) or from its use. Manufacturer shall not be liable under this warranty if: a) The water heater or any of its component parts has been subject to misuse, alteration, neglect or accident, or b) The water heater has not been installed in accordance with the applicable local plumbing and/or building code(s) and/or regulation(s), or c) The water heater has not been installed in accordance with the printed manufacturer's instructions, or d) The water heater is not continuously Controlled Energy Corp. 340 Mad River Park Waitsfield, VT 05673 800-798-8161 www. protankless. com/tech supplied with potable water. The OWNER and not the Manufacturer or his representative shall be liable for and shall pay for all field charges for labor or other expenses incurred in the removal and/or repair of the product or any expense incurred by the owner in order to repair the product. [. . . ]