User manual HOOVER H3000

[. . . ] Owner's Manual FloorMATETM with SpinScrubTM Brushes The Hard Floor Cleaner English § pp. 24-31 Thank you for selecting a HOOVER product. This cleaner inspected and packaged carefully before being shipped from the factory. If you should happen to need assistance during assembly or operation: Visit us online at www. hoover. com to find the service outlet nearest you (click on the "Service" button) or Call 1-800-944-9200 for an automated referral of authorized service outlet locations (U. S. only) or Call 1-330-499-9499 to speak with a representative in our Consumer Response Center. PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE. Review this manual before operating cleaner. www. hoover. com Fill in and retain The model and serial number are located at the bottom of the back of the cleaner body. [. . . ] Place cleaner handle in upright, locked position. 6 To remove tank, press down on release button and pivot tank forward. Carry tank to a sink. Cap must be locked in place for proper performance and to prevent leaking. Position bottom of tank into cleaner. Press latch and snap tank into place. Continued 7 How to Empty Turn cleaner off and disconnect from electrical outlet. Although not necessary for satisfactory performance, it is recommended that the recovery tank be emptied after dry vacuuming and before wet operation. It may need to be refilled at this time. 2-16 L 2-17 N M To remove tank, press down on release button (L) and pivot tank forward. Lift up on tank lid latch (M) and remove the tank lid (N). Empty tank. 2-18 2-19 2-20 O P Q R Dry or loose debris will also collect on the filter screen (O) in the tank lid. The filter screen may also be cleaned by rinsing it under running water. Clean this filter when suction is low or reduced. To replace lid, align tab (P) on lid with hole on front of tank (Q). Snap latch over tabs (R) on back of tank. To replace tank, insert bottom of tank into cleaner and pivot top portion until it is locked in place. To Clean Filter 2-21 2-22 S Turn cleaner OFF and disconnect from electrical outlet. Remove loose debris from filter by either brushing or tapping the filter. How to clean Recommended Cleaning Sequence Use your HOOVER `FloorMate' Cleaner to: 1. Follow the chart to set the controls for each cleaning step. OPERATION Dry Vacuuming BRUSH CONTROL SWITCH "Wet/Dry Pickup" (UP) WET/DRY PEDAL Dry Pickup Wet Cleaning "Wet Scrub" (DOWN) Wet Pickup/ Scrub Wet Pickup/ Scrub Wet Pickup "Wet/Dry Pickup" (UP) See Page 6 Figs. 2-6 and 2-7 for complete instructions on the control switch and pedal. To Clean Floor (vinyl, tile, linoleum, etc. ) 1. Fill solution tank with Machine Formula LYSOL® Floor Cleaning Concentrate and water, according to instructions for Figs. Do not use pine or solvent based cleaning concentrates in your cleaner. Dry hands and plug cleaner into a properly grounded outlet. 3-1 The cleaner's suction will pick up the dirty solution throughout cleaning. To greatly enhance drying of the floor surface, release trigger and move wet control switch up to the "WET/DRY PICKUP" setting. To continue cleaning another area, move wet control switch down to "WET Scrub". NOTE: When switching between wet cleaning and wet pickup, it is not necessary to turn the cleaner off. Simply move the control switch back and forth between the two settings. Empty recovery tank or clean the filter when the motor sound becomes higher in pitch and there is a loss of suction (see "Automatic Shut-Off", page 7). A 6. Step on handle release pedal and lower handle to operating position; turn cleaner ON. [. . . ] · Recovery tank not properly installed · Ensure that recovery tank is installed properly (Fig. · Ensure recovery tank filter and filter lid are properly installed (Fig. Problem: Cleaner pushes a line of dry debris in front of it Possible cause Possible solution · Cleaner not set for dry operation · Press wet/dry pedal to "DRY PICKUP" position. · Debris is too large to clear squeegee · Tip nozzle off floor by pushing down on handle. [. . . ]