User manual HOOVER AE140

[. . . ] If the appliance is installed on a carpeted floor ensure that the ventilation holes on the base of the appliance are not obstructed. N) If the appliance is not running properly or breaks down, switch it off, turn off the tap and do not tamper with the appliance. Consult only the Authorised Technical Support Service for possible repair and ask them to use original spare parts. Failure to comply with the above can compromise the safety of the appliance. [. . . ] Once a programme is selected the programme selector remains stationary on the selected programme till cycle ends. Switch off the washing machine by turning the selector to "OFF". Note: The programme selector must be returned to the "OFF" position at the end of each cycle or when starting a subsequent wash cycle prior to the next programme being selected and started. Buttons indicator light These light up when the relevant buttons are pressed. If an option is selected that is not compatible with the selected programme then the light on the button first flashes and then goes off. 11 O TABLE OF PROGRAMMES PROGRAM FOR: PROGRAMME SELECTOR ON: WEIGHT MAX kg TEMP. For the first time, the tub does not carry out complete rotations but uses pulse movements with pauses inbetween. Specifically, the tub does there delicate clock wise movements, pauses, and then does 3 anti clock wise movements. This type of washing action guarantees a care and delicately only equalled by hand washing and is applied to the programmes below identified with the symbol . 5 2 1 4 3 6 5 2 1 3 6 4 Tessuti delicati Acrilici - 40 2 Fino a: 40° RESISTANTS FABRICS The programmes have been designed for a maximum wash and the rinses, with spin intervals, ensure perfect rinsing. The final spin gives more efficient removal of water. SPECIAL SILK PROGRAMME This washing machine also has a gentle Silk and Hand Wash programme cycle. This programme allows a complete washing cycle for garments specified as `Hand Wash only' and laundry items made from Silk on the fabric label. The programme has a maximum temperature of 30° and concludes with 3 rinses and no final spin. WOOLMARK PROGRAMME The special cycle, certified by WOOLMARK, enables to thoroughly wash garments without damaging them. The programme has a maximum temperature of 40° and concludes with 3 rinses and a short spin. 1 5 2 1 3 6 4 MIXED AND SYNTHETIC FABRICS The main wash and the rinse gives best results thanks to the rotation rhythms of the drum and to the water levels. - amount of laundry: it is possible to reduce the amount of detergent when washing only a small amount of laundry. Additional laundry aids Water softener, means less detergent can be used where water hardness is classed as hard to very hard. Prewash substances, for the programmed treatment of stains prior to the main wash. Using them means the subsequent wash can be at a low temperature or with bleach-free detergents. Fabric softener, prevents static build-up in synthetic fabrics and softens fabrics. If you own a tumble dryer, clothes are softened even without the use of a fabric softener. Dosage for powder detergent For normal and low concentration detergents: for normally soiled laundry choose a programme without prewash. Put 1/4 of the detergent in compartment "1", 3/4 in compartment "2" of the drawer. When using water softeners, first put in the detergent, then add the softener to compartment "2". For highly concentrated detergents not in single dose format, follow what is shown on pack exactly as regards type and amount of dosage. To avoid the difficulty of checking if the detergent has been taken up, use the dosage aids provided in the detergent packaging. Do not put solvents in the washing machine!Keep detergents and other laundry products out of children's reach. Before pouring in the detergent check that there are no foreign bodies in the detergent drawer. [. . . ] - Carrying out more rinse cycles does not serve any purpose in such cases. CUSTOMER SERVICE AND GUARANTEE Your new appliance is fully guaranteed by the manufacturer for 12 months against electrical/mechanical breakdown excluding: A. Any faults which occur due to bad installation or misuse of the machine. Any faults which occur due to repair of, or interference with, the machine by any person not authorised by the manufacturer to carry out service. Any faults which arise from parts fitted to the machine which are not the manufacturers original parts. [. . . ]