User manual HONEYWELL Y6630D1007

[. . . ] 9 1. 1. 1. General safety instructions Commissioning the relay module HC60NG Danger Danger to life through electric shock!Contacts that are open are live. Ensure that the device is deenergised. Observe the valid local regulations during the installation. WARNING Insufficient data transfer!Interference of the relay module HC60NG in the device through metallic objects or further frequency devices. Mount the device with a distance of at least 30 cm to metallic objects such as wall boxes or boiler housings according to the DECT standard, etc. [. . . ] Interference of the radio receiver in the device through metallic objects or further radio devices. WARNING Ensure there is sufficient distance to metallic objects. Mount the device with a distance of at least 1 m to radio devices such as radio headphones, cordless phones according to the DECT standard, etc. Select another installation site if the radio interference cannot be rectified. Fig. Insert the supplied AA batteries with the correct battery polarity (see Fig. 9: Positioning the room unit HCW 80 Place the room unit HCW 80 at the installation site. 12: Battery polarity and send button 2 The batteries have to be replaced when the red LED at the room unit HCW 80 flashes (see section "9 Changing batteries"). 1 Fig. 10: Removing the housing cover Place the housing cover in position above and snap it down (see Fig. 13). Mark the drill holes according to the drilling template (see Fig. 13: Placing housing cover in position 6 Checking 4. 4. 1. Checking System check 5. 2. Failed teach-in If the teach-in has failed: See section "5. 1 Assignment to the relay module HC60NG". Improve the data transfer. Adjust the set point of the room unit HCW 80 to 30 °C. If the room temperature is >30 °C the relay module HC60NG is switched on. If the room temperature is <5 °C the relay module HC60NG is switched OFF. Improving the data transfer 4. 2. Radio transmission check When selecting the operating site of each device ensure that the distance to radio devices such as radio headphones, cordless phones, etc. Do not install the devices over metallic wall connecting sockets and at least 30 cm away from the cover of the heat generator. Correct the installation site of the room unit HCW 80 if necessary. The room unit HCW 80 can send a test signal to the assigned relay module HC60NG in order to test the signal strength. Keep the teach-in button of the HCW 80 pressed for at least 15 sec until the red LED of the HCW 80 is OFF. The LED of the HCW80 flashes briefly at every test signal the HCW 80 is sending. The field strength is indicated by flashing of the red LED of the HC60NG (1 = sufficient, 5 = strong). 6. Communication loss If the wireless communication is not successful optimise the placement of the HCW80. The test mode is terminated automatically after 5 min. The test mode can also be terminated by removing the batteries or by pressing the teachin button. When the RF communication is lost for a period of 1 h, the red LED of the relay module HC60NG is ON to indicate that no RF messages have been received during the last hour. When RF communication is re-established the relay module HC60NG will automatically return to normal operation mode. See chapter "10 Help with problems" for possible cause and problem solving. 7. Factory reset of relay module HC60NG 5. Teach-in (single devices only) The teach-in operation is required if the relay module HC60NG and the room unit HW80 are not pre-bounded e. g. new single devices or product replacement. Keep the button of the HC60NG pressed for at least 15 sec. The resetting was successful when the red LED flashes rapidly (1/9 ON/OFF). 5. 1. Assignment to the relay module HC60NG After the factory reset the HC60NG looses the communication with the HCW 80. [. . . ] 10, Page 6). Insert the batteries with the right polarity into the battery compartment (see Fig. Place the housing cover on at the top and latch it in downwards (see Fig. Help with problems Problem Teach-in failed Cause Batteries inserted incorrectly Radio connection failure Remedy RF RF operation band Insert the batteries correctly. WEEE directive 2002/96/EC ­ Waste Electrical and Electronic Equipment directive 10. 3. [. . . ]