User manual HONEYWELL TH6110D

[. . . ] All rights reserved. FocusPROTM TH6110D/TH6220D Programmable Thermostat Table of contents About your new thermostat Thermostat features . . . . . . . . . . . . . . . . . . . . . . . . 2 Programming at a glance . . . . . . . . . . . . . . . . 3 Quick reference to controls. . . . . . . . . . . . 4 Quick reference to display. . . . . . . . . . . . . . 5 Programming & Operation Set time and day. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Select fan setting (auto/on) . . . . . . . . . . . . 7 Select system setting (heat/cool). . . . . . 8 Using program schedules. . . . . . . . . . . . . . . . 9 Program schedule overrides . . . . . . . . 12 Auto-changeover (heat/cool) . . . . . . . . 14 Compressor protection . . . . . . . . . . . . . . . . 15 Adaptive Intelligent RecoveryTM . . . . 16 1 Appendices Battery installation . . . . . . . . . . . . . . . . . . . . . . . . 17 In case of difficulty . . . . . . . . . . . . . . . . . . . . . . 18 Customer assistance. . . . . . . . . . . . . . . . . . . . . . 20 Accessories/replacement parts . . . . 20 Limited warranty . . . . . . . . . . . . . . . . . . . . . . . . . . 21 This thermostat is ready to go!To prevent possible compressor damage, do not operate cooling system when outdoor temperature is below 50°F (10°C). Operating Manual About your new thermostat Congratulations on the purchase of your new Honeywell thermostat. It has been designed to give you many years of reliable service and easy-to-use, push-button climate control. Features · · · · · · · Separately programmable weekday/weekend schedules. [. . . ] Set to the time you go to bed and the temperature you want overnight (usually an energy-saving level). 9 62 ° Operating Manual EnergyStar® settings for maximum cost savings This thermostat is pre-set to use EnergyStar® program settings. We recommend these settings, since they can reduce your heating/cooling expenses by as much as 33%. (See next page to adjust times and temperatures of each time period. ) Heat (Mon-Fri) Wake (6:00 am) Cool (Mon-Fri) Heat (Sat-Sun) Cool (Sat-Sun) Leave (8:00 am) Return (6:00 pm) Sleep (10:00 pm) 70 ° 62 ° 70 ° 62 ° 75 ° 83 ° 75 ° 78 ° 10 [Or cancel period] [Or cancel period] 70 ° 62 ° 70 ° 62 ° [Or cancel period] [Or cancel period] 75 ° 83 ° 75 ° 78 ° FocusPROTM TH6110D/TH6220D Programmable Thermostat To adjust program schedules Set Clock/Day/ Schedule Fan Auto System Cool Done Set Day Set Schedule Set Schedule Heat Setting 8:00 Leave Done CancelPeriod AM 62 ° 1 Press SET CLOCK/DAY/SCHEDULE, then SET SCHEDULE. 3 Press or to set the temperature for this time period, then press NEXT. 5 Press NEXT to set weekend time periods (Sat-Sun), then press DONE to save & exit. Note: Make sure the thermostat is set to the system you want to program (Heat or Cool). Note: You can press CANCEL PERIOD to eliminate unwanted time periods (except Wake). 11 Mon Tue Wed Thu Fri Next Operating Manual Program schedule override (temporary) Press to temporarily adjust temperature Inside 69 ° Temporary Heat Setting 6:30 Fan Auto AM 75 ° Press or to immediately adjust the temperature. This will temporarily override the temperature setting for the current time period. The new temperature will be maintained only until the next programmed time period begins (see page 10). For example, if you want to turn up the heat early in the morning, it will automatically be lowered later, when you leave for the day. To cancel the temporary setting at any time, press RUN SCHEDULE. Run Schedule System Heat Press to cancel temporary setting and resume program schedule Note: Make sure the thermostat is set to the system you want to control (heat, cool or auto). 12 FocusPROTM TH6110D/TH6220D Programmable Thermostat Program schedule override (permanent) Press to permanently adjust temperature Inside Heat Setting 69 ° Hold 6:30 Fan Auto AM 75 Press HOLD to permanently adjust the temperature. This will override the temperature settings for all time periods. The "Hold" feature turns off the program schedule and allows you to adjust the thermostat manually, as needed. Whatever temperature you set will be maintained 24 hours a day, until you manually change it, or press RUN SCHEDULE to cancel "Hold" and resume the programmed schedule. ° Run Schedule System Heat Press to cancel "Hold" setting and resume program schedule Note: Make sure the thermostat is set to the system you want to control (heat, cool or auto). 13 Operating Manual Auto Changeover (heat/cool) Set Clock/Day/ Schedule Fan Auto System Auto Auto Changeover is a feature used in climates where both air conditioning and heating are used on the same day. When the system is set to Auto, the thermostat automatically selects heating or cooling depending on the indoor temperature. Heat and cool settings must be at least 3 degrees apart. The thermostat will automatically adjust settings to maintain this 3-degree separation (called "deadband"). The 3-degree separation between heating and cooling set temperatures is fixed, and cannot be changed. 14 Press until screen displays "Auto" Note: The Auto system setting may not appear, depending on how your thermostat was installed. FocusPROTM TH6110D/TH6220D Programmable Thermostat Built-in compressor protection Inside 75 ° Cool Setting 6:30 Fan Auto AM 75 ° This feature helps prevent damage to the compressor in your air conditioning or heat pump system. Damage can occur if the compressor is restarted too soon after shutdown. This feature forces the compressor to wait for a few minutes before restarting. During the wait time, the display will flash the message Cool On (or Heat On if you have a heat pump). When the safe wait time has elapsed, the message stops flashing and the compressor turns on. Set Clock/Day/ Schedule Cool On System Cool Message flashes until safe restart time has elapsed 15 Operating Manual Adaptive Intelligent RecoveryTM (AIR) Adaptive Intelligent Recovery eliminates guesswork when setting your schedule. It allows the thermostat to "learn" how long your furnace and air conditioner take to reach the temperature you want. Just set your program schedule to the time you want the house to reach your desired temperature. The thermostat then turns on the heating or cooling at just the right time to reach your scheduled temperature at your scheduled time. For example: Set the Wake time to 6 am, and the temperature to 70°. The heat will come on before 6 am, so the temperature is 70° by the time you wake at 6. Note: When Adaptive Intelligent Recovery is in effect, the thermostat will display "In Recovery". 16 FocusPROTM TH6110D/TH6220D Programmable Thermostat Battery replacement Press and pull to remove Batteries are optional (to provide backup power) if your thermostat was wired to run on AC power when installed. [. . . ] This warranty gives you specific legal rights, and you may have other rights which vary from state to state. If you have any questions concerning this warranty, please write Honeywell Customer Relations, 1985 Douglas Dr, Golden Valley, MN 55422 or call 1-800-4681502. In Canada, write Retail Products ON15-02H, Honeywell Limited/ Honeywell Limitée, 35 Dynamic Drive, Scarborough, Ontario M1V4Z9. 23 Automation and Control Solutions Honeywell International Inc. [. . . ]