User manual HONEYWELL T7412E

[. . . ] ROOM TEMPERATURE SENSOR T7412A, B, C, D, E PRODUCT DATA Honeywell FEATURES · · · · · · · PT1000, PT100, NTC20k, or BALCO 500 temperature sensing element Sensing range 0. . . 50 °C (32. . . 122 °F) High-precision sensor elements Attractive housing Occupied/unoccupied slide switch Fan speed switch Push-button for time extension or other purposes and LED for status indication Honeywell °C 20 25 15 30 Honeywell SPECIFICATION Ambient Limits Operating temperature Transport and storage temp. [. . . ] T7412A1000 T7412A1018 T7412A1026 T7412A1059 T7412B1008 T7412B1016 T7412B1024 T7412B1040 T7412B1057 T7412C1006 T7412C1030 T7412D1004 T7412E1001 T7412E1027 temperature sensing element* NTC 20k PT1000 BALCO 500 PT100 NTC 20k + CPA PT1000 + CPA BALCO 500 + SPA 15. . . 30 °C PT1000 + SPA 15. . . 30 °C PT1000 + CPA NTC 20k + CPA + occ. /unoccupied switch PT1000 + CPA and occ. /unoccupied switch NTC 20k + CPA + Fan Speed Switch NTC 20k + push-button + C-Bus connector NTC 20k + push-button + indication LED For potentiometer values and circuits, see Fig. * Other temperature sensing elements and different housing colors are available, upon request. Models model no. / function T7412A T7412B T7412C T7412D T7412E temperature sensor remote setpoint adjustment control-point adjustment occupied/ unoccupied switch Honeywell Honeywell Honeywell Honeywell occupancy extend push-button fan speed switch Honeywell LED or PIT C-Bus connector Honeywell °C °C °C auto 0 12 3 20 25 °C 15 30 - + - + - + EN0B-0240GE51 R1009 2 T7412A, B, C, D, E ROOM TEMPERATURE SENSOR INSTALLATION · · · · Mount these units at the inside wall of the room to be heated or air conditioned, away from doors, windows, and heat sources. 1. 5 m above the floor and at minimum 50 cm away from the nearest wall. Do not mount in niches, book shelves, behind cabinets or curtains, or where it could be exposed to solar radiation. Seal the conduit opening to avoid false temperature measurement due to draft from the conduit. The offset due to wire resistance per 10 m of distance from the sensor to the controller is stated in the following table: type of wire 0. 5 mm2 (AWG20) 1. 0 mm2 (AWG17) 1. 5 mm2 (AWG15) temperature offset PT100 BALCO 500 1. 8 °C 0. 3 °C (3. 24 °F) (0. 54 °F) 0. 9 °C 0. 15 °C (1. 62 °F) (0. 27 °F) 0. 6 °C 0. 1 °C (1. 08 °F) (0. 1 °F) NOTE: Use shielded wiring in areas with high EMI. Keep 15 cm (5. 9'') minimum distance between sensor lines and 230 Vac power lines. wiring run sensor to controller maximum length 200 m (660 ft) PT1000 0. 18 °C (0. 324 °F) 0. 09 °C (0. 162 °F) 0. 06 °C (0. 108 °F) Connections for T7412A: T7412A1000 1 T7412A1018 1 T7412A1026 1 T7412A1059 1 NTC 20kohm 2 PT1000 2 BALCO 500 2 PT100 2 Connections for T7412B: T7412B1016 1 1 Connections for T7412C: T7412B1024 1 T7412B1040 T7412B1008 (NTC) T7412C1057 (PT1000) 3 T7412C1006 (NTC) T7412C1030 (PT1000) 3 PT1000 2 2 BALCO 500 2 PT1000 PT1000 or NTC20kohm PT1000 or NTC20kohm 4 953 ohm CPA 100 ohm 4 10k ohm SPA 10k ohm 15 °C 4 10k ohm SPA 10k ohm 15 °C 4 4 CPA 100k ohm 6 CPA 100k ohm 5 * 5 5 6 5 30 °C 11k ohm 6 30 °C 11k ohm 6 *occupancy switch Connections for T7412D: T7412D1004 3 Connections for T7412E: T7412E1001 3 1 2 3 T7412E1027 LED NTC20kohm 4 NTC20kohm 5 6 7 A * NTC20kohm 4 5 6 *occupancy extend push-button fan-speed switch auto-OFF-I-II-III 8 10 5 6 C-bus B connector * *occupancy extend push-button Fig. [. . . ] Printed in Germany EN0B-0240GE51 R1009 107 (4. 21") 60 (2. 36") 60 (2. 36") [. . . ]