User manual HONEYWELL T7200

[. . . ] T7270A2001 See the W7070A2000 ZAPP Receiver Installation Instructions (EN1B-0396GE51) for information on installing wireless systems. APPLICATION The T7270A2001/T7200 ZAPP Wireless Wall Modules are used for intelligent room temperature control. · The T7200 ZAPP Wireless Wall Module measures the room temperature and transmits the measured values to the W7070A2000 ZAPP Wireless Receiver. · The T7270A2001 ZAPP Wireless Wall Module measures the room temperature and transmits the measured values to the W7070A2000 ZAPP Wireless Receiver. [. . . ] · The T7270A2001 ZAPP Wireless Wall Module measures the room temperature and transmits the measured values to the W7070A2000 ZAPP Wireless Receiver. Additionally, the T7270A2001 allows the room setpoint temperature to be adjusted. The T7270A2001/T7200 transmit the data to the W7070A2000 at 868. 3 MHz. 2 Additional Features of T7270A2001 The T7270A2001 ZAPP Wireless Wall Module has the following functions (in addition to those of the T7200): Adjustment wheel at which you can change the room temperature setpoint directly. The adjustment range amounts to ± 12 °C, starting from the basic value of 20 °C (in position 0). 1 Fig. · All rights reserved EN1B-0397GE51 R1207A T7270A2001/2019 WIRELESS WALL MODULE Remove the housing cover of the T7270A2001 / T7200 (see Fig. 4). R2 RED LED TEACH-IN BUTTON 4 86 99 R2 4 68 82 Fig. Battery polarity and "Teach-In" button Insert the supplied AA batteries with the correct battery polarity (see Fig. If appropriate, put the adjustment wheel back in, rotated by 180°, until it has the position shown. 5). 3 EN1B-0397GE51 R1207A T7270A2001/2019 WIRELESS WALL MODULE CHANGING BATTERIES Change the batteries if the red LED of the room temperature sensor flashes and the device is not in test mode. Dispose of the batteries according to the local statutory requirements and not together with the usual domestic refuse. TECHNICAL DATA Batteries Frequency 1. 5 V, type LR06, AA 868. 3 MHz (transmitter) WEEE DIRECTIVE 2002/96/EC At the end of the product life, dispose of the packaging and product in a corresponding recycling center. Only use 1. 5 V batteries of the type LR06, AA. Insert the new batteries with the correct polarity into the battery compartment (see Fig. Place the housing cover on at the top and latch it in downwards (see Fig. 5). TROUBLESHOOTING Problem Teach-in failed Cause Batteries inserted incorrectly Radio connection failure Remedy Insert the batteries correctly. No measured data at W7070A2000 Batteries inserted incorrectly Radio connection failure Module not assigned or assigned incorrectly Eliminate interference sources (metal, wireless devices). If appropriate, repeat. Manufactured for and on behalf of the Environmental and Combustion Controls Division of Honeywell Technologies Sàrl, Ecublens, Route du Bois 37, Switzerland by its Authorized Representative: Honeywell GmbH Böblinger Straße 17 71101 Schönaich, Germany Tel. : (++49) (0) 7031 637 01 Fax: (++49) (0) 7031 637 493 http://europe. hbc. honeywell. com Subject to change without notice. [. . . ] 5). TROUBLESHOOTING Problem Teach-in failed Cause Batteries inserted incorrectly Radio connection failure Remedy Insert the batteries correctly. No measured data at W7070A2000 Batteries inserted incorrectly Radio connection failure Module not assigned or assigned incorrectly Eliminate interference sources (metal, wireless devices). If appropriate, repeat. Manufactured for and on behalf of the Environmental and Combustion Controls Division of Honeywell Technologies Sàrl, Ecublens, Route du Bois 37, Switzerland by its Authorized Representative: Honeywell GmbH Böblinger Straße 17 71101 Schönaich, Germany Tel. : (++49) (0) 7031 637 01 Fax: (++49) (0) 7031 637 493 http://europe. hbc. honeywell. com Subject to change without notice. Printed in Germany This document is definitive for the enclosed product and replaces all previous publications. [. . . ]