User manual HONEYWELL T4700

[. . . ] 14 3 69-1396--2 Specifications Models: T4700A: SPST; makes heating circuit on temperature fall. Breaks both sides of 240 volt line with switch in OFF position. Wiring: 6 in. (150 mm) stranded copper leadwires, suitable for connection to aluminum wiring if approved special service CO/ALR connectors are used. Electrical Ratings (Noninductive): 3800W, 16A maximum; 500W, 2A minimum at 240V, 60 Hz. Sensing Element: Electronic thermistor. Temperature Ratings: Operating Range: -20 to +104°F (-30° to +40°C). [. . . ] Sharp instruments like pens and pencil points can damage the keys. Homeowner Programming IMPORTANT After programming is complete, the device reverts to normal Run mode within five minutes, if no key was pressed, and any new setting is stored in its memory. The thermostat is flexible and can be programmed to meet your lifestyle. Four time periods are available: WAKE is the time the thermostat turns on the equipment after an energy saving period. When deciding what time to set for your WAKE period, include extra lead time, depending on the outside temperature and 69-1396--2 6 See Tables 2 - 6 to program your thermostat. Table 2. Step 1 Press This Key Display Shows Description Displays day of the week. 2 Displays changed day of the week. 3 Displays hour of the day. 4 Displays changed hour of the day. 5 Displays minute of the day. 6 Displays changed minute of the day. 7 69-1396--2 Table 3. Step 1 Press This Key Display Shows Description Scrolling through the display shows the first day to program, beginning with Monday. Displays WAKE time. 2 3 4 5 6 Displays changed WAKE time in ten-minute increments. Displays LEAVE time. NOTE: Continue through LEAVE, RETURN, and SLEEP periods using the same procedure to set the time and temperature for each period. To easily copy one day schedule to another day, see Table 4. 69-1396--2 8 Table 4. Step 1 Press This Key Display Shows Description Selects and displays the day to be copied; for example, MOnday. (NOTE: Repeat sequence to copy additional days. ) NOTE: To exit the programming mode: 1) press and hold the Prog key for three seconds and the display returns to Run mode, or 2) during the programming session, after five minutes elapsed time with no program change, the display reverts to Run mode. Simply keep pressing the Prog key until you arrive at the desired mode. 9 69-1396--2 Table 5. Step Temporary (TEMP) Mode Indefinitely Overriding a Program Hold (HOLD) Mode Changes to HOLD mode and controls at the HOLD temperature indefinitely. Press This Key Display Shows Description Changes to TEMPorary mode and controls at a new temperature until the next scheduled event (for example, RETURN). Temporarily Overriding a Program Programming Additional Functions To change display or function (for example, 69-1396--2 10 to °C or °F temperature setting, or to 7-day or 5-1-1 programming), see Table 6. Table 6. Press This Key Display Shows Description Press and hold both the Prog and Func keys. Initially a random fourdigit/letter display occurs (for example, FF FF). Press (+) key to change mode to 7-day programming (or back to 51-1 programming). Then adjust using the (+) or (-) keys. Convert 5-1-1 to 7 day. NOTE: To exit the programming mode: 1) press and hold the Prog key for three seconds and the display returns to Run mode, or 2) during the programming session, after five minutes elapsed time with no program change, the display reverts to Run mode. [. . . ] This warranty shall not apply if it is shown by Honeywell that the defect or malfunction was caused by damage which occurred while the product was in the possession of a consumer. Honeywell's sole responsibility shall be to repair or replace the product within the terms stated above. HONEYWELL SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. [. . . ]