User manual HONEYWELL HB 05

[. . . ] 2 Overview · In the case of Version HB 15 with a connected vane anemometer*: Opening or closing the shutters depending on the wind forces (wind protection*) Use the wind sensor HWS 40 to control the awnings. You can connect further external sensors to the sun module: · A temperature sensor to the HB 05 (alternatively to the temperature sensor in the housing) · A temperature sensor and a vane anemometer to the HB 15 3 Overview Scope of supply (1) Sun module (2) Mounting bracket (3) 2 batteries 1. 5 V, type LR 06 (mignon) Additionally in the Sun module HB 15 scope of supply (4) Connection cable (HCV 23) (5) Vane anemometer 4 Mounting Mounting Safety instructions The sun module has a radio transmitter whose function can be impaired by metallic objects or radio devices. When selecting the mounting site, ensure that there is sufficient distance to metallic objects and radio devices. The brightness and temperature sensors in the inside of the module have been adapted to the housing state. [. . . ] Connecting the sun module to the distribution box Remove the sun module from the mounting bracket and open the battery compartment. Insert the plug of the connecting cable into the connecting socket of the sun module (1). Insert the connecting cable. The yellow conductor at the open end of the connecting cable is not required to connect external sensors. 9 Mounting If necessary, shorten the yellow conductor at the open cable end. Connect the connecting cable (HCV 23) to the terminal strip in the distribution box as shown in the diagram below. T Cable to the external temperature sensor W Cable to the vane anemometer HCV 23 Connection cable to the sun module Green Black Red Yellow External temperature sensor Vane anemometer Ground unengaged Close the battery compartment. Insert the sun module back into the mounting bracket. 10 Mounting 3. Mounting external sensor(s) The maximum cable length between the sun module and the temperature sensor amounts to 3 m, between the sun module and the vane anemometer 8 m. Select a suitable mounting site. Mount external sensor(s) in accordance with the mounting instruct- ions of the manufacturer. Prepare the cables to the required length. Lay the cables from the external sensor(s) to the distribution box. 4. Connecting external sensor(s) to the distribution box Wire the cable to the vane anemometer in accordance with the diagram on Page 9. Wire the cable to the vane anemometer in accordance with the diagram on Page 9. Mounting of the external sensor(s) has been completed. 11 Mounting Teach-in If you use external sensors, these have to be mounted before you carry out the teach-in. Activating the teach-in mode at the Hometronic Manager The Hometronic Manager shows the Hometronic standard display, e. g. : WE 03. 07. 2002 11:15 no lifestyle active LIVING 20. 0 C Press the Dial button. The cursor flashes in the bottom line. Turn the Dial button to the right until Hometronic SET DATE/TIME ACTIVATE LIFESTYLE LIVING 20. 0 C MENU SET DATE/TIME ACTIVATE LIFESTYLE LIVING 20. 0 C LIFESTYLES TIME PROGRAMS DISPLAY SETTINGS "Menu" is selected. Press the Dial button. The following text is displayed: 12 Mounting Turn the Dial button to the left until "Settings" is selected. LIFESTYLES TIME PROGRAMS DISPLAY SETTINGS INSTALLATION DE-INSTALLATION FUNCTION EXPANSION SENSOR FUNCTION HEATING/COOLING SHUTTERS DEVICES/LIGHTS SENSOR HEATING/COOLING SHUTTERS DEVICES/LIGHTS SENSOR SENSOR-1 SENSOR-2 SENSOR-3 SENSOR-4 SENSOR-1 SENSOR-2 SENSOR-3 SENSOR-4 BRIGHT TEMP Press the Dial button. The following text is displayed: Press the Dial button. The following text is displayed: Turn the Dial button to the left until "Sensor" is selected. Press the Dial button. In this example, 2 sensors are already assigned: Turn the Dial button to the left until a free sensor selected. (e. g. "Sensor 3") is BRIGHT TEMP 13 Mounting Press the Dial button. SENSOR-1 BRIGHT SENSOR-2 TEMP SENSOR-3 . In order to check whether the radio connection is ensured for later operation, the sun module should remain as near as possible to the mounting site during the teach-in mode. 2. Activating the teach-in mode at the sun module Remove the sun module from the mounting bracket. Open the battery compartment. Close the battery compartment and insert the sun module back into the mounting bracket. The sun module is assigned to the Hometronic Manager. 14 Mounting 3. Display at the Hometronic Manager if the teach-in is successful SENSOR-1 BRIGHT SENSOR-2 TEMP SENSOR-3 * SENSOR-4 The Hometronic Manager recognizes that the Sun module HB 05 has two different sensors (brightness and temperature) and therefore reserves the next sensor correspondingly. After a brief period, the asterisk is SENSOR-1 BRIGHT replaced by the designation for the SENSOR-2 TEMP SENSOR-3 BRIGHT respective sensor type. [. . . ] Depending on the measured data provided by the vane anemometer the Hometronic Manager activates the automatic wind protection for shutters. The shutters cannot be operated as long as the wind protection is active. 17 Technical data Technical data Degree of protection Operating temperature range Storage temperature range Max. [. . . ]