User manual HONEYWELL F59A

[. . . ] EFFICIENCY: 90% efficiency rating based on National Bureau of Standards Dust Spot Method using atmospheric dust and American Society of Heating, Refrigerating, and Air-Conditioning Engineers Standard 52-76. CLEAN AIR DELIVERY RATINGS: cfm Dust Tobacco Smoke Pollen 288 270 239 m3/hr 560 450 340 m3/hr 489 459 406 Fig. 1--F59A components. PREFILTER ELECTRICAL RATINGS: Nominal Current and Power Consumption (max): 120 Vac, 60 Hz 220 Vac, 50 Hz Fan Speed High Medium Low A 1. 0 . 74 . 65 W 110 80 65 A . 60 . 45 . 35 W 120 70 55 INTERLOCK SWITCH: Interrupts supply circuit to unit when cover is opened. Available in walnut or light oak finish (light oak not available in Canada). [. . . ] To avoid burns, let the cell cool completely before removing, or wear protective gloves when removing the cell. Remember that water may be trapped in the tubes that support the collector plates. Wipe the ionizer wires and contact board on end of cell with a small, damp cloth, using your thumb and forefinger. You may wish to rerun the wash and/or rinse cycle with the dishwasher empty if you see dirt or residue from washing the cell. If dirt or residue seems excessive, wash the cell more often or try a different detergent. Inspect the cell for bent plates; bend back to normal to prevent arcing. Rinse the cell with a hard spray of very hot water; rinse the tub clean, then fill the tub with clean hot water and soak for 5 to 15 minutes. Wipe the ionizer wires and contact board on end of cell by using your thumb and forefinger and holding a small, damp cloth. Car Wash Use the hand sprayer at a coin-operated car wash to wash the cell. Hold the nozzle at least 2 ft [0. 6m] away from the unit to avoid damage from the high pressure stream of water. Rinse until the water draining from the cell no longer feels slippery. REINSTALLING CELL, PREFILTER AND CARBON POSTFILTER s Inspect the cell for broken ionizer wires and bent collector plates. s Slide the dry filter into the filter guides, with directional arrow pointing toward the center of the electronic air cleaner cabinet. The directional arrow is very small, and is located on the end of the filter frame. s Gently vacuum the inside and outside of the air cleaner cabinet with the brush attachment of vacuum cleaner, or dust with a soft cloth. s Slide in the dry cell so the directional arrow (located on the side of the cell) points toward the center of the air cleaner cabinet. The metal tab on the cover must fit in the slot at the end of the cabinet, and the interlock under the cover must connect with the air cleaner cabinet for operations. 3--Cover must fit correctly for operation. THE METAL TAB ON THE COVER MUST FIT IN THE SLOT METAL TAB SLOT METAL TAB INTERLOCK THE INTERLOCK UNDER THE COVER MUST CONNECT WITH THE AIR CLEANER CABINET CAUTION HAZARDOUS CHEMICAL. NOTE: Always wash the cell first, then the prefilter, to keep heavy prefilter lint from getting caught in the cell. Use a container such as a laundry tub or trash container that is large enough to hold the cell. Dissolve about 3/4 cup automatic dishwashing detergent in enough hot water to cover the cell. If the detergent does not dissolve readily, or forms a scum on the water, try another brand, or use softened water. [. . . ] This will reduce ozone production about 20 to 25 percent, and reduce efficiency about 7 to 10 percent depending on actual airflow delivered by the furnace blower. Turn off power to the air cleaner; tip unit upside down and remove bottom plate to access power supply. Regular replacement of the carbon filter (every 3 to 6 months) will also help reduce ozone odor. 68-0086--5 8 F59A ELECTRICAL TROUBLESHOOTING Fig. 10--Use an ohmmeter to check the cell for short circuits as instructed in Fig. [. . . ]