User manual HILTI WSR 36-A

[. . . ] WSR 36-A Bedienungsanleitung Operating instructions Mode d'emploi Istruzioni d'uso Manual de instrucciones Manual de instruções Gebruiksaanwijzing Brugsanvisning Bruksanvisning Bruksanvisning Käyttöohje de en fr it es pt nl da sv no fi el 1 1 2 34 5 +" +± + 9 6 87 2 3 3/5 4 6 1 4 5 6 2/4 min. 6mm 3/5 3 1 2 4 1 6 5 2 4 3 7 6 7 8 10 9 9 8 9 1 1 10 2 11 min. 40mm 12 1­ 6 3 2 13 WSR 36A cordless reciprocating saw It is essential that the operating instructions are read before the power tool is operated for the first time. Always keep these operating instructions together with the power tool. Ensure that the operating instructions are with the power tool when it is given to other persons. Contents 1. EC declaration of conformity Page 15 16 18 18 19 22 24 25 26 26 27 27 1 These numbers refer to the corresponding illustrations. [. . . ] thickness for which the saw is designed and do not use unsuitable saw blades (reciprocating saw blades of the wrong size or not equipped with a ¹/" connection end). 5. 2. 4 Battery tool use and care a) Observe the special instructions applicable to the transport, storage and use of Liion batteries. c) Batteries must not be opened or dismantled, squashed, heated to temperatures over 100°C or incinerated. A risk of fire, explosion or injury through contact with caustic substances may otherwise result. d) Do not use batteries other than those approved for use with the applicable power tool or appliance. Use of other batteries or use of the battery en 21 en for purposes for which it is not intended presents a risk of fire and explosion. batteries with cracks, broken parts, bent or pushedin and/or pulledout contacts). g) Ensure that the outer surfaces of the battery are clean and dry before inserting it in the corresponding charger. Read the operating instructions for the charger for further information about the charging procedure. 5. 2. 5 Electrical safety may become live, for example, when an electric cable is damaged accidentally. Exposure to dust at a poorly ventilated workplace may result in damage to the health. 5. 2. 7 Personal protective equipment Before beginning work, check the working area (e. g. using a metal detector) to ensure that no concealed electric cables or gas and water pipes are present. External metal parts of the power tool The user and any other persons in the vicinity must wear suitable eye protection, a hard hat, ear protection, protective gloves and breathing protection while the power tool is in use. 6. Turn the blade holder locking sleeve counterclockwise and hold it pressed down. Release the locking sleeve and allow it to move back to its original position. 6. 2 Adjusting the contact shoe 5 Adjustment of the contact shoe, on the one hand, allows maximum use to be made of saw blade length and, on the other, can improve access in tight corners (the contact shoe engages at intervals of 6 mm). Press the contact shoe adjustment button and hold it in this position. Release the contact shoe adjustment button. 6. 1 Changing the saw blade CAUTION Wear protective gloves. Check that the connection end of the insert tool is clean and lightly greased. NOTE Use only saw blades equipped with a ¹/" connection end (fig. Turn the blade holder locking sleeve counterclockwise and hold it in this position. [. . . ] Turn the locking sleeve as far as it will go and remove the saw blade. en The battery is discharged or fitted incorrectly. The stroke rate is set too low. The control switch is not pressed fully. Disposal CAUTION Improper disposal of the equipment may have serious consequences: The burning of plastic components generates toxic fumes which may present a health hazard. Batteries may explode if damaged or exposed to very high temperatures, causing poisoning, burns, acid burns or environmental pollution. [. . . ]