User manual HILTI TKT 1300

[. . . ] Don't Overreach Keep proper footing and balance at all times. such as blades, bits, culters. 15. Remove Adjusting Keys and Wrenches Form a habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 1 6. Avoid Unintentional Electric Shock Prevent body contact with grounded surfaces. They can be caught in moving parts Rubber gloves and nonskid footwear are recommended when working outdoors. [. . . ] Don't Abuse Cord Never carry tool by cord or yank it to disconnect from receptacle. Disconnect Tools When noi in use, before servicing, and when changing accessories, Parts Before further use of the 21. Wear Ear Protectors Wear ear protectors when using for extended penods. Double Insulation The Hilti TKT 2000/TKT 1300 are double-insulated for extra operator protection. The tools are equipped with a two-wire cord and two-prong plug which can be used on standard 115 volts outlets. When servicing use only identical replacement Extension Cords Use an extension cord heavy enough to carry the current your tool requires. An undersized cord will cause a drop in voltage, resulting in loss of power and overheating. The following list shows the cor rect size to use depending on cord length. lf in doubt, use the next heavier gauge. Note: The smaller the gauge number, the heavier the cord. The following are recommended American Wire Gauges (AWG) Cord length up to 25 ft" up 50 ft. up to 200 ft. AWG '18 to to to 14 tz 10 10 for vour TKT tools. SAVE THESE INSTRUCTIONS Operation Power Source: Before connecting your drill to an outlet, make sure that the power supply is 1 15 voits AC. Variable speed control switch The speed can be varied steplessly between zero and the maximum r. p. m. Locking collar To ensure different types of screws (with and without sealing rings) a'e driven lo the right depth (c'sunk, flush or with stand-off), the drive is disengaged via the depth locator (5). The collar must lirst be pulled away The driving power is transmitted via a claw coupling. They disengage again when the depth gauge touches the work surface (fig. lt is thus possible to connect the screw and stationary bit or adaptor while the machine is runninq. from the housing to free it before it can be adjusted. When the collar is turned in the direction of the arrow the screw is driven less deeo or in the other direction deeoer. 5. Torgue adjustment Turn the locking collar (4) to the desired torque setting (2-18). Be sure not to exceed the 18 setting to prevent possible tool damaoe. 2. Lockbutton for continuous operation. Depress switch (1) fully, press in lockbutton (2) and then release both of them. Caution!lf it iams for more than 2 to 3 seconds the motor can be damaged. After adjusting_the collar it must pressedtowardsthehousingtosetit. Fig. be. 6, Changing depth locators a'd bitdnUi SetterS lefUright-hand rotation 3. Reversing switch for 1 Fi9. 2 By pressing the reversing switch (3) the direction of rotation is selected. Press switch (3) to the right for clockwise rotation of screw Press switch (3) to the left for counterclockwise rotation of screw. Depth locators (5) and bits etc. [. . . ] This self-drilling fastener eliminates -and its related problems of "burn through" and weldino cumbe-rsome equiPment. ITEM NO. 000803007 000824524 00080301 5 ITEM DESCRIPTION 6-20x3/B PPH #2 6-20X3/B PPH #2 BULK 6-20X7116 PPH #2 6-20x112 PPH #2 6-20x112 HWH #2 B-18X112 HWH #2 8-1BX112 HWH #2 BULK B-1BX112 HWH #2 STLG B-18X112 PPH #2 B-18X112 PPH #2 BULK 8. 18X112 PPH #2 STLG B-18X3/4 HWH #2 B-18X3/4 HWH #2 BULK B-18X3/4 HWH #2 STLG 8-18x3/4 PPH#2 B-18X1 HWH #2 B-18X1 HWH #2 STLG B-18X1 PPH #2 8-18X1 PPH #2 BULK q- QTY/BX 1, 000 20, 000 1, 000 15, 000 12, 000 1, 000 10, 000 10, 000 1, 000 10, 000 10, 000 1, 000 8, 000 8, 000 1, 000 5, 000 5, 000 1, 000 8, 000 ITEM NO. 000803296 000803304 ITEM DESCRIPTION 12-24X718 HWH #4 STLG QTY/BX 4, 500 3, 500 000855569 000855577 000803254 12-24X1 1/4 HWH #4 STLG 000824532 000855361 000803056 This hiqh performance selldrilling fastener the Dri[it - drills and tastens in metal having a total thickness of 1 14" to 1 12". with the simple use of a Kwik-Tapper, welding and other exoensive and complicated assembly proceduies are eliminated. Very liftle torque is required to drive this faslener as compared to #5 point screws. - 000842542 000855478 000803270 000824557 000855395 000803064 000855585 000855338 000803072 000824565 000803312 000875419 12-24X1 1/4 HWH DRIL. IT STLG 12-24X1 1/4 DRIL-IT STLG BULK 500 4, 000 #3 POINT WOOD TO METAL Self-drillinq fasleners make lloor, intenor 000855601 000803338 000824573 000855619 000855627 10-16X112 HWH #2 10-16X3t4 HWH #2 10-16X3/4 HWH #2 BULK 10-16X1 HWH #2 12-14X1 HWH #2 8, 000 1, 000 6, 000 5, 000 4, 000 q 000855650 000855635 000824649 000855809 00085581 7 000803700 000824656 000855825 000803809 000824664 000855833 000855841 point provides fastening capability up to . 1 75". [. . . ]