User manual HILTI TE76-ATC

[. . . ] TE 76-ATC USA CDN E P Operating instructions Mode d'emploi Instrucciones de uso Manual de instruções 1­ 8 9­16 17­24 25­32 334212 334212 1 ¸ ¹ µ This Product is Listed Ce produit est homologué Producto homologado por Este produto está registrado C US Protective grounding Mise à la terre de Always wear safety glasses Porter des lunettes de protection. Gafas de seguridad Use sempre óculos de segurança Always wear protective gloves protection Conexión a tierra Aterramento de proteção Wear respiratory protection when the work causes dust Porter des gants Porter un casque Pour les travaux prode sécurité. Guantes de Protección Protección respiseguridad auditiva ratoria en trabajos que produzcan polvo Use sempre luvas Use sempre fones Use máscaras de proteção de proteção para respiratórias para os ouvidos se proteger da poeira Always wear ear protectors 2 3 4 5 6 7 8 9 10 11 12 13 14 15 It is essential that the operating instructions are read before the tool is operated for the first time. Ensure that the operating instructions are with the tool when it is given to other persons. In these operating instructions, this symbol indicates points of particular importance to safety. [. . . ] g) Press the control switch fully and continue drilling at full power. When drilling a through hole, reduce drilling speed shortly before the drill bit breaks through. Active Torque Control The TE76-ATC is equipped with the Active Torque Control system in addition to the mechanical torque limiting clutch. This system aids in maintaining control of the tool in the drilling mode. on rebar, ATC is designed to help stop the tool, reducing the risk of an unwanted spin. When the ATC system has activated, the tool can be restarted by releasing the control switch and re-engaging it after the the motor has stopped rotating ("click"sound signals readiness for use). 5 Operation Operating from generators and transformers This tool can be used on a generator and jobsite transformers if it meets the following requirements: ­ AC output 2600 W minimum; 24 A minimum ­ 120 V AC nominal; min. 132 V under all conditions ­ frequency 50­60 Hz; never to exceed 65 Hz ­ high dynamic automatic voltage regulator Do not use other power tools on the generator/ transformer at the same time. Switching other tools on/off can cause undervoltage and/or overvoltage spikes which could damage the tool. Inserting the insert tool a) Unplug the supply cord from the electrical socket to prevent unintentional starting. b) Check that the connection end of the insert tool is clean and lightly greased. Check that the sealing lip of the dust shield Always choose a working position in which the tool is free to rotate in a counter-clockwise direction (as seen by the operator). Drilling using the depth gauge (accessory) We recommend the use of the depth gauge for drilling holes to the exact depth required. The depth gauge rod is offset in order to reduce deviations caused by tilting the tool and to make it easier to adjust the drilling depth . Assembly : Position the depth gauge on the top side of the power tool so that the two positioning lugs engage in the depressions for the flange screws. Press the depth gauge on to the tool until the two rear retaining lugs engage in the tool casing. Insert the depth gauge rod into the depth gauge from the front, with the offset end towards the front of the tool. Adjusting drilling depth : Slide the depth gauge rod to the required drilling depth. Drilling without hammering action Drilling without hammering action is possible with insert tools with a special connection end. Insert tools of this kind are available in the Hilti insert tool program. Wood drill bits or steel drill bits with smooth shank can be fitted, for example, in the keyless chuck and used for drilling without hammering action. The function selector switch must be engaged in the hammer drilling position ( ). f) Connect the supply cord to the power supply. [. . . ] Additional claims are excluded, unless stringent national rules prohibit such exclusion. In particular, Hilti is not obligated for direct, indirect, incidental or consequential damages, losses or expenses in connection with, or by reason of, the use of, or inability to use the tool for any purpose. Implied warranties of merchantability or fitness for a particular purpose are specifically excluded. For repair or replacement, send tool and/or related parts immediately upon discovery of the defect to the address of the local Hilti marketing organization. [. . . ]