User manual HILTI TE76

[. . . ] TE 76 USA CDN E P Operating instructions Mode d'emploi Instrucciones de uso Manual de instruções 1­8 9­16 17­24 25­32 334215 334215 1 ¸ ¹ µ This Product is Listed Ce produit est homologué Producto homologado por Este produto está registrado C US Protective grounding Mise à la terre de Always wear safety glasses Porter des lunettes de protection. Gafas de seguridad Use sempre óculos de segurança Always wear protective gloves protection Conexión a tierra Aterramento de proteção Wear respiratory protection when the work causes dust Porter des gants Porter un casque Pour les travaux prode sécurité. Guantes de Protección Protección respiseguridad auditiva ratoria en trabajos que produzcan polvo Use sempre luvas Use sempre fones Use máscaras de proteção de proteção para respiratórias para os ouvidos se proteger da poeira Always wear ear protectors 2 3 4 5 6 7 8 9 10 11 12 13 14 TE 76 Combihammer It is essential that the operating instructions are read before the tool is operated for the first time. Ensure that the operating instructions are with the tool when it is given to other persons. In these operating instructions, this symbol indicates points of particular importance to safety. [. . . ] perforated brick), drilling at the half-power setting can be of advantage. f) Bring the tip of the drill bit into contact with the work surface at the position where the hole is to be drilled and press the control switch slowly. g) Press the control switch fully and continue drilling at full power. When drilling a through hole, reduce drilling speed shortly before the drill bit breaks through. Drilling using the depth gauge (accessory) We recommend the use of the depth gauge for drilling holes to the exact depth required. The depth gauge rod is offset in order to reduce deviations caused by tilting the tool and to make it easier to adjust the drilling depth . Assembly : Position the depth gauge on the top side of the power tool so that the two positioning lugs engage in the depressions for the flange screws. Press the depth gauge on to the tool until the two rear retaining lugs engage in the tool casing. Insert the depth gauge rod 5 Operation Operating from generators This tool can be used on a generator if it meets the following requirements: - AC output 2000 W minimum; 18 A minimum - 120 V AC nominal; min. 132 V under all conditions - frequency 50­60 Hz; never to exceed 65 Hz - high dynamic automatic voltage regulator Do not use other power tools on the same generator at the same time. Switching other tools on/off can cause undervoltage and/or overvoltage spikes which could damage the tool. Inserting the insert tool a) Unplug the supply cord from the electrical socket to prevent unintentional starting. b) Check that the connection end of the insert tool is clean and lightly greased. Clean it and grease it if nec- into the depth gauge from the front, with the offset end towards the front of the tool. Adjusting drilling depth : Slide the depth gauge rod to the required drilling depth. Drilling without hammering action Drilling without hammering action is possible with insert tools with a special connection end. Insert tools of this kind are available in the Hilti insert tool program. Wood drill bits or steel drill bits with smooth shank can be fitted, for example, in the keyless chuck and used for drilling without hammering action. The function selector switch must be engaged in the hammer drilling position ( ). If you do not intend to chisel in constant-on mode, always push the red sliding switch located above the control switch to the left position. Otherwise, the control switch could unintentionaly be locked in the constant-on position when chiseling. Never operate the function selector switch while the motor is running. When chiseling, the selector switch must always be engaged in the chiseling position ( ). [. . . ] 8 hours more after the service indicator light comes on, until the automatic cut-out will be activated. Take the tool to a Hilti service center for planned routine maintenance when the service indicator light illuminates. Have your tool repaired by a Hilti service center. Insert tools and accessories Use only insert tools with TE-Y connection end . Hilti power tools have been designed to work optimally as a system together with Hilti insert tools. [. . . ]