User manual HILTI TE705

[. . . ] When not in use, tools should be stored in dry, and high or locked-up place ­ out of reach of children. It will do the job better and safer at the rate for which it was intended. Don't force small tool or attachment to do the job of a heavy-duty tool. Don't use tool for purpose not intended ­ for example ­ don't use circular saw for cutting tree limbs or logs. [. . . ] The tool is equipped with a 3-conductor cord and 3-prong grounding type plug to fit the proper grounding type receptacle. The green (or green and yellow) conductor in the cord is the grounding wire. Never connect the green (or green and yellow) wire to a live terminal. If your unit is for use on less than 150 V, it has a plug that looks like that shown in sketch (A) in Figure «Grounding Methods». An adapter, see sketch (B), is available for connecting sketch (A) type plugs to 2-prong receptacles. The green-colored rigid ear, lug, or the like, extending from the adapter must be connected in a permanent ground, such as a properly grounded outlet box. 0 6 10 12 6 10 12 16 GROUNDING METHODS Not recommended 17. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this instruction manual. Only use accessories and attachments which are given in the operating instructions or in the respective catalogue. The use of accessories or insert tools or attachments other than those speci- metal screw cover of grounded outlet box grounding pin (A) (B) 26. Use only 3-wire extension cords that have 3prong grounding-type plugs and 3-pole receptacles that accept the tool's plug. When servicing use only identical replacement parts. Save these instructions. 2 englisch 1 Hilti TE 705 breaker Technical data Power input: Voltage (versions): Current input: Frequency: Machine weight: Dimensions: Hammering speed under load: Single impact energy: Chiselling performance in medium-hard concrete: Chisels: 1030 W 120 V ~ 10 A 50­60 Hz 6. 5 kg (14. 3 lbs) 515×215×115 mm (20. 3×8. 5×4. 5 in) 1940/2740 blows/min. (30 in3/min) with standard SM36 chisel Pointed, narrow flat, wide flat, extra wide flat, hollow, channel (narrow or wide) scoop, in standard version TE-Y 2 Kit supplied with the machine: Plastic case, cleaning cloth, Hilti insert tool grease, operating instructions 3 1 2 3 4 Eye protection must be worn Chuck: Chisel cutting edge adjustment to 18 positions Permanent lubrication Adjustable side handle On/off switch for continuous running Electronic r. p. m. regulation for improved operating convenience Hammering power regulation: max. = 50% Protection class I (grounded tool) Service indicator with warning lamp Right of technical modifications reserved. 5 This Product is UL listed and CSA certified R The respective regulations of your trade association and the enclosed safety precautions must be observed. Do not use this product in any way other than as directed by these operating instructions. 3 Before operating the machine, please note: Hold the machine securely with both hands while working. Regularly check the security of the stance or position from which you are working. [. . . ] Push the chisel in further against the resistance of the retaining mechanism and release the locking sleeve. To remove the chisel: Pull back the locking sleeve and remove the chisel. 3: Chisel adjustment Pull back the locking sleeve as far as it will go (1), rotate the chisel into the desired position (2), release the locking sleeve and the chisel engages in position (3). 4 Chisel maintenance: Resharpening: When reshparpening wide-flat, narrow-flat and pointed chisels which are not badly worn at the cutting edge, take care to avoid overheating the surface (no discoloration!). [. . . ]