User manual HILTI TE56ATC

[. . . ] TE 46/TE 46-ATC TE 56/TE 56-ATC Operating instructions Mode d'emploi Manual de instrucciones Manual de instruções en fr es pt 369440 *369440* 1 1 2 3 4 11 5 10 9 8 7 6 UL listed to US and Canadian safety standards Homologué UL (conforme aux normes de sécurité américaines et canadiennes) Producto homologado según normas de seguridad americanas y canadienses Produto homologado de accordo com as normas de segurança americanas e canadianas C R US 2 3 3 2 2 1 4 1 3 4 6 5 4 1 5 3 1 2 6 7 2 3 1 5 3 2 1 7 8 6 4 2 8 9 2 4 3 2 1 6 3 7 2 1 4 8 6 5 5 2 10 203086 TE-Y 18 SDS max TE 46 / TE 46-ATC TE 56 / TE 56-ATC TE 46/TE 46-ATC/TE 56/TE 56-ATC combihammer It is essential that the operating instructions are read before the tool is operated for the first time. Ensure that the operating instructions are with the tool when it is given to other persons. 1. General information 1. 1 Signal words and their meaning -CAUTIONUsed to draw attention to a potentially dangerous situation which could lead to minor personal injury or damage to the equipment or other property. -NOTEUsed to draw attention to an instruction or other useful information. [. . . ] Check that the connection end of the insert tool is clean and lightly greased. Clean it and grease it if necessary. 6. 4 Hammer drilling ­ full hammering power -CAUTION- this procedure until the hammering mechanism begins to operate. Active torque control (TE 46-ATC/TE 56-ATC) The TE 46-ATC/TE 56-ATC is equipped with an active torque control system in addition to the mechanical clutch. This system offers additional safety while drilling by quickly switching off the tool, for example, when the drill bit sticks on contacting a reinforcing bar or when the insert tool is tilted unintentionally, thus preventing uncontrolled rotation around the longitudinal axis of the drill bit. When the torque control system has become activated, the tool can be returned to normal operating mode by releasing pressure on the control switch, waiting until the motor has stopped rotating and then reapplying pressure to the control switch. (An audible "click" indicates that the tool is again ready for operation). Always choose a working position in which the electric tool is free to rotate in a counter-clockwise direction (as seen by the operator). 6. 5 Drilling without hammering action ( ) (only TE 46-ATC/TE 56-ATC) 1. Engage the function selection switch in the "rotary drilling" position. Bring the side handle into the desired position and check that it is correctly fitted and properly secured. Position the tip of the drill bit at the point where the hole is to be drilled. Begin drilling at low speed, increasing speed only after the drill bit has become centered in the hole. 6. 6 Chiseling ( / ) -NOTEThe chisel can be locked in 24 different positions (in 15° increments). Flat and shaped chisels can thus always be brought into the optimum position for the job on hand. Turn the function selection switch to the "chisel adjustment" position until it engages. Pivot the side handle into the desired position and check that it is fitted and secured correctly. (Alternatively, when chiseling, the tool may be held at the section of the housing behind the chuck. ) 3. Turn the function selection switch to the "chiseling" position until it engages. en Drilling may cause splintering of the material. Wear eye protection, protective gloves and breathing protection if no dust removal system is used. -CAUTION The tool and the drilling operation emit noise. Engage the function selection switch in the "hammer drilling / full hammering power" position. Bring the side handle into the desired position and check that it is correctly fitted and properly secured. ­ Full drilling power: Full drilling power is always activated after plugging the supply cord into the mains socket. [. . . ] (See "Before use". ) Control switch not fully pressed Press the control switch as far as it will go. "Reduced power" button activated Press the "reduced power" button (fig. Function selection switch not engaged After rotation has stopped, move the function selection switch until it engages. Chuck sleeve not pulled back fully Pull the chuck sleeve back as far as it will go and remove the insert tool. [. . . ]