User manual HILTI TE2

[. . . ] TE 2/TE 2-S/TE 2-M USA CDN es pt Operating instructions 1­ 8 Mode d'emploi 9­16 Manual de instrucciones 17­24 Manual de instruções 25­32 376009 *376009* 1 ³ · ¿ » TE2 TE 2-S TE2-M This Product is Certified Ce produit est homologué Producto homologado por Este produto está registrado Always wear safety glasses Porter des lunettes de protection. Gafas de seguridad Use sempre óculos de segurança Always wear protective gloves Porter des gants de sécurité. Guantes de seguridad Use sempre luvas de proteção Always wear ear protectors Wear respiratory protection when the work causes dust Porter un casque Pour les travaux produisant antibruit. Protección auditiva Protección respiratoria en trabajos que produzcan polvo C US Use sempre Use máscaras respiratórias fones de proteção para se proteger da poeira para os ouvidos 2 TE2-M 3 TE2-M 4 5 6 7 TE2 7a 7b 7 TE2-S 7a 7b 7c 7 TE2-M 7a 7b 7c 7d 8 9 10 TE 2/TE 2-S/TE 2-M Rotary Hammer General information It is essential that the operating instructions are read before the tool is operated for the first time. [. . . ] The following items are supplied: power tool, (quickrelease chuck TE2-M), operating instructions, grease, toolbox. The following conditions must always be observed when the tool is in use: ­ The tool must be connected to an alternating current electric supply in compliance with the information given on the type plate. ­ The tool must not be used in places where the surrounding conditions may present a risk of explosion. Main features of the tool ­ Electrical protection class II (double insulated) Z ­ Mechanical torque-limiting clutch ­ Grip and side handle with vibration absorption ­ TE-C chuck with twist lock ­ TE-C insert tool system ­ Variable speed switch ­ Drilling modes ­ Gearing and hammering mechanism with permanent grease lubrication ­ Pivotable side handle ­ Mechanical depth gauge ­ Interface for quick-release chuck (TE2-M) ­ Precision hammering action (TE2-S / TE2-M) ­ High spindle speed without hammering action (TE2-M) 4 The tool is designed for the following uses: Use TE 2 / TE 2-S / TE 2-M: Hammer drilling in concrete, masonry and natural stone TE 2-S / TE 2-M: Drilling with precision hammering action in perforated brick, tiles and marble TE 2 / TE 2-S: Drilling in wood, drywall panels and metal Required insert tools Diameter range Drill bits with TE-C connection end Drilling in concrete: ­ Short hammer drillbits Anchor holes of 4­20 mm (3/16­3/4) dia. ­ Long hamer drill bits Through holes of 4­20 mm (3/16­3/4) dia. Drill bits with TE-C connection end Drilling in brittle materials: ­ TE-CX hammer drill bits Anchor holes of 4­20 mm (3/16­3/4) dia. ­ Thin-barrel core bits Cutting sockels of 25­68 mm (1­25/8) dia. Quick-release chuck with TE-C adaptor for insert tools with cylindrical shank or hexagonal shank for rotary-only drilling Wood drill bits 4­20 mm (3/16­3/4) dia. Push the insert tool into the chuck as far as it will go and then rotate the insert tool until the driving grooves engage and the tool can be pushed all the way into the chuck. Turn the chuck (quick twist) towards the () symbol to lock the insert tool in the chuck . Removing the insert tool Unplug the supply cord from the electrical socket to prevent unintentional starting. b) Turn the chuck towards the ( ) symbol and pull out the insert tool . Drilling Hammer drilling / precision hammering action (TE2-S / TE2-M) a) Insert the drill bit into the chuck. b) Turn the function selection switch to the hammer drilling position ( ) until the switch mechanism and the gearing are engaged 7a ). c) Use of the precision hammering action ( ) is advantageous when drilling in brittle materials (e. g. e) Pivot the side handle, with or without the depth gauge, to the desired angle and tighten the handle to lock it in this position. f) Bring the tip of the drill bit into contact with the work surface at the position where the hole is to be drilled and press the control switch slowly. g) Press the control switch fully and continue drilling at full power. Rotary-only drilling (without hammering action) (TE2 / TE2-S) Turn the function selection switch to the drilling position ( ) 7b . When the switch is in this position, only the rotary movement is transmitted to the TE-C insert tool or chuck adaptor for insert tools with cylindrical shanks. Rotary-only drilling (without hammering action) (TE2-M) Turn the function selection switch to the 1st gear or 2nd gear drilling position 7b 7d . When the switch is in these positions, only the rotary movement is transmitted to the TE-C insert tool or quick-release chuck. [. . . ] Implied warranties of merchantability or fitness for a particular purpose are specifically excluded. For repair or replacement, send tool and/or related parts immediately upon discovery of the defect to the address of the local Hilti marketing organization provided. Accessories Use only insert tools with TE-C connection end . Hilti power tools have been designed to work optimally as a system together with Hilti insert tools. Accordingly, highest performance and longest life expectancy can be achieved when you use this power tool with Hilti insert tools. [. . . ]