User manual HILTI TE16-C

[. . . ] TE16 / TE16-C / TE16-M Bedienungsanleitung Operating instructions Mode d'emploi Istruzioni d'uso Gebruiksaanwijzing Manual de instruções Manual de instrucciones Brugsanvisning Käyttöohje Bruksanvisning Bruksanvisning Kasutusjuhend Lietoanas pamÇc¥ba de en fr it nl pt es da fi no sv el et lv 287428 *287428* 1 1 2 3 5 6-M TE 1 4 6 7 C 16TE 2 3 3 3 2 2 1 TE 16 -M 1 TE 16 -M 4 4 4 4 5 6 1 5 3 1 2 6 5 4 1 () ( ) () ( ) 6 7 () ( ) 8 (( )) (( )) 7 8 2 2/4 () ( ) 1 1 3 9 10 1 3 4 1 2 11 12 6-M TE 1 L R TE 16/-C/-M rotary hammer It is essential that the operating instructions are read before the tool is operated for the first time. Ensure that the operating instructions are with the tool when it is given to other persons. Operating controls and parts Chuck Function selector switch Control switch Forwards/reverse switch Side handle with depth gauge Theft protection system (accessory for TE 16-M available as option) Supply cord 1. General information 1. 1 Safety notices and their meaning -CAUTIONDraws attention to a potentially dangerous situation that could lead to minor personal injury or damage to the equipment or other property. -NOTEDraws attention to instructions and other useful information that help the user to employ the product efficiently. [. . . ] Operation 7. 1. 4 Fitting the insert tool (TE-T) -NOTERemove the depth gauge from the side handle in order to avoid injury. Check that the connection end of the insert tool is clean and lightly greased. Check that the sealing lip of the dust shield is clean and in good condition. Clean the dust shield if necessary or replace it if the sealing lip is damaged. 7. 1. 5 Removing the insert tool (TE-T) -NOTERemove the depth gauge from the side handle in order to avoid injury. 7. 1. 6 Removing the chuck (TE-C und TE-T) -NOTERemove the depth gauge from the side handle in order to avoid injury. Pull the retaining ring on the chuck toward the front and hold it in this position. 7. 1. 7 Fitting the chuck (TE-C und TE-T) -NOTERemove the depth gauge from the side handle in order to avoid injury. Push the chuck onto the guide tube on the tool and release the sleeve. Turn the chuck until it is heard to engage. CAUTION: In the event of the drill bit sticking, the tool will pivot about its own axis. Always use the tool with the side handle fitted and hold it securely with both hands applying an opposing torque so that the clutch releases in the event of the drill bit sticking. Wear protective gloves when changing insert tools. 7. 1 Preparing the tool for use 7. 1. 1 Adjusting the depth gauge 1. Release the side handle clamping mechanism by turning the handle in a counter-clockwise direction. Tighten the side handle securely by turning the handle in a clockwise direction. Check that the connection end of the insert tool is clean and lightly greased. Check that the sealing lip of the dust shield is clean and in good condition. Clean the dust shield if necessary or replace it if the sealing lip is damaged. Push the connection end of the insert tool into the chuck and, while applying slight pressure, rotate the insert tool until it engages in the guide grooves. Push the insert tool further into the chuck until it is heard to engage. Pull the insert tool out of the chuck. 19 7. 2 Operating the tool 7. 2. 1 Activating the tool (theft protection system) (TE 16-M) (accessory available as option) Please refer to the operating instructions for the TPS theft protection system. (The tool is now under power and ready for activation by contactless communication with a valid electronic activation key. ) 2. The tool is activated and ready for use as soon as the yellow theft protection indicator lamp no longer lights. [. . . ] (see 6. 3) Set the switch to forwards rotation. en Control switch defective. Function selector switch not engaged. No hammering action. The tool does not achieve full power. Drill bit doesn't rotate. Chuck sleeve not pulled back fully. Disposal Most of the materials from which Hilti electric tools are manufactured can be recycled. The materials must be correctly separated before they can be recycled. [. . . ]