User manual HILTI TE 70-ATC

[. . . ] TE 70-ATC / TE 70 Bedienungsanleitung Operating instructions Mode d'emploi Manual de instrucciones Istruzioni d'uso Gebruiksaanwijzing Brugsanvisning Bruksanvisning Bruksanvisning Käyttöohje Manual de instruções Lietoßanas pamåcîba Instrukcija Kasutusjuhend de en fr es it nl da no sv fi pt el lv lt et 1 1 2 3 7 4 6 5 8 9 + 2 3 4 1 1 4 3 2 5 2 5 4 5 6 1 5 4 1 3 2 6 1 7 3 2 5 2 7 8 6 2 4 8 5 a. m 7:30 07 9 1 2 1 4 2 8 6 2 3 3 TE 70ATC / TE 70 combi hammer It is essential that the operating instructions are read before the power tool is operated for the first time. Always keep these operating instructions together with the power tool. Ensure that the operating instructions are with the power tool when it is given to other persons. Contents 1. EC declaration of conformity Page 15 16 18 19 20 22 22 25 26 27 27 28 1 These numbers refer to the corresponding illustrations. [. . . ] CAUTION Check that the clamping band is engaged in the groove provided on the power tool. 6. 2 Use of extension cords and generators or transformers Please refer to section 2 "Description". 6. 1 Fitting and adjusting the side handle 2 1. Release the side handle clamping band by turning the handle counterclockwise. 7. The user must be prepared for sudden sticking and stalling of the insert tool. CAUTION Use clamps or a vice to hold the workpiece securely. CAUTION In accordance with the applications for which it is designed, the power tool produces a high torque. Always use the side handle and hold the power 22 CAUTION The collar at the front end of the gearing section is not to be used as a gripping surface. 7. 1 Preparing for use CAUTION Wear protective gloves when changing insert tools as the insert tools get hot during use. Check that the connection end of the insert tool is clean and lightly greased. Check that the sealing lip of the dust shield is clean and in good condition. Clean the dust shield if necessary or have it replaced if the sealing lip is damaged. Push the insert tool into the chuck and rotate it while applying slight pressure until it engages in the guide grooves. Push the insert tool further into the chuck until it is heard to engage. 7. 2 Operation CAUTION Switch the power tool on only after bringing it into the working position. CAUTION Do not operate the function selector switch while the motor is running. 7. 2. 1 TPS theft protection system (optional) NOTE The power tool may be equipped with the optional theft protection system. If the power tool is equipped with this feature, it can be unlocked and made ready for operation only through use of the corresponding TPS key. Hold the TPS key or the TPS watch strap buckle against the lock symbol. The power tool is unlocked as soon as the yellow theft protection indicator LED no longer lights. NOTE If, for example, the electric supply is briefly interrupted due to a power failure or disconnected when moving to a different workplace, the power tool remains ready for operation for approx. In the event of a longer interruption, the TPS key must be used again to unlock the power tool. 7. 2. 1. 2 Activation of the theft protection system for the power tool NOTE Further detailed information on activation and use of the theft protection system can be found in the operating instructions for the theft protection system. 7. 2. 2 Hammer drilling 6 NOTE Working at low temperatures: The hammering mechanism works only when the power tool has reached a minimum operating temperature. [. . . ] The power tool is too cold. No hammering action. The power tool doesn't start and the LED blinks red. The power tool doesn't start and the indicator lamp blinks yellow. The power tool doesn't achieve full power. A fault has occurred in the power tool. The carbon brushes are worn. The power tool has not been unlocked (power tools with optional theft protection system). [. . . ]