User manual HILTI TE 7-A

[. . . ] 12 13 TE 7-A Hilti Corporation LI-9494 Schaan Tel. : +423 / 234 21 11 Fax: +423 / 234 29 65 www. hilti. com Bedienungsanleitung Operating instructions Mode d'emploi Manual de instrucciones Istruzioni d'uso de en fr es it nl da no sv fi pt el lv lt et 14 Gebruiksaanwijzing Brugsanvisning Bruksanvisning Bruksanvisning 36 Volt Li-Ion 3. 3 Ah 36 Volt Li-Ion 3. 3 Ah Käyttöohje Manual de instruções Lietoßanas pamåcîba Instrukcija Kasutusjuhend Hilti = registered trademark of Hilti Corp. , Schaan W 3091 0706 10-Pos. 1 1 Printed in Liechtenstein © 2006 Right of technical and programme changes reserved S. & O. 202925 /A 202925 *202925* 1 2 3 7 1 1 2 43 2 1 2 2 1 1 3 4 3 4 1 8 1 36 Volt 2 2/5 1 1 3 5 6 7 8 5 4 1 2 5 3 6 9 1 1 2 43 2 3 4 1 1 6 3 36 Volt Li-Ion 3. 3 Ah 10 2 11 5 6 7 8 1/4 TE 7 A cordless rotary hammer It is essential that the operating instructions are read before the power tool is operated for the first time. Always keep these operating instructions together with the power tool. [. . . ] NOTE The belt adapter cannot be used in conjunction with Li ion batteries. Observe the instructions given in the section "Safety rules" on safe use of the belt adapter. en 7. Check that the sealing lip of the dust shield is clean and in good condition. Clean the dust shield if necessary or replace it if the sealing lip is found to be damaged (please refer to the "Care and maintenance" section). Push the insert tool into the chuck and rotate it while applying slight pressure until it engages in the guide grooves. Push the insert tool further into the chuck until it is heard to engage. Release the side handle clamping band by turning the handle counterclockwise. This also clamps the depth gauge in position. CAUTION In the event of the drill bit sticking, the power tool will pivot about its own axis. Always use the power tool with the side handle fitted and hold it securely with both hands so that the resulting opposing force causes the slip clutch to release in the event of the drill bit sticking. 7. 1 Preparing for use 7. 1. 1 Fitting the insert tool 5 CAUTION Wear protective gloves when changing the insert tool. Set the forward / reverse switch to the middle position or remove the battery from the power tool. Check that the connection end of the insert tool is clean and lightly greased. Clean it and grease it if necessary. 25 7. 1. 3 Removing the insert tool 7 CAUTION Wear protective gloves when changing insert tools as the insert tool will get hot during use. Set the forward / reverse switch to the middle position or remove the battery from the power tool. 7. 1. 4 Removing the chuck 8 CAUTION Remove the depth gauge from the side handle and the insert tool from the chuck in order to avoid injury. NOTE Set the selector switch to the "Chiseling" position before removing the chuck. Set the forward / reverse switch to the middle position or remove the battery from the power tool. 7. 1. 5 Fitting the chuck 9 CAUTION Remove the depth gauge from the side handle and the insert tool from the chuck in order to avoid injury. NOTE Set the selector switch to the "Chiseling" position before removing the chuck. Set the forward / reverse switch to the middle position or remove the battery from the power tool. Grip the chuck sleeve, pull it forward and hold it securely in this position. Slide the chuck onto the guide tube from the front and then release the sleeve. [. . . ] The function selector switch is not engaged or is set to "Chiseling" or "Chisel adjustment". 29 Fault The insert tool can't be released. The tool makes no progress. Possible cause The chuck is not pulled back fully. Remedy Pull the chuck back as far as it will go and remove the insert tool. The forward/reverse switch is set to Set the forward/reverse switch to reverse rotation. Disposal CAUTION Improper disposal of the equipment may have serious consequences: The burning of plastic components generates toxic fumes which may present a health hazard. [. . . ]