User manual HILTI TE 500

[. . . ] TE 500 / TE 500-AVR Hilti Corporation LI-9494 Schaan Tel. : +423 / 234 21 11 Fax: +423 / 234 29 65 www. hilti. com Bedienungsanleitung Operating instructions Mode d'emploi Manual de instrucciones Istruzioni d'uso Gebruiksaanwijzing Brugsanvisning Bruksanvisning Bruksanvisning Käyttöohje Manual de instruções Lietoßanas pamåcîba Instrukcija Kasutusjuhend de en fr es it nl da no sv fi pt el lv lt et ar Hilti = registered trademark of Hilti Corp. , Schaan W 3256 0107 00-Pos. 1 1 Printed in Liechtenstein © 2007 Right of technical and programme changes reserved S. & O. 378616 / A 378616 *378616* 1 2 3 4 1 1 5 6 4 2 3 3 2/5 1 2 9 4 5 1 2 4 3 5 6 3 1 2 7:30 a. m 6 1 3/5 4 8 7 2 07 TE 500 / TE 500AVR breaker It is essential that the operating instructions are read before the power tool is operated for the first time. Always keep these operating instructions together with the power tool. [. . . ] External metal parts of the power tool may become live, for example, when an electric cable is damaged accidentally. b) Check the power tool's supply cord at regular intervals and have it replaced by a qualified specialist if found to be damaged. Check extension cords at regular intervals and replace them if found to be damaged. Do not touch the supply cord or extension cord if it is damaged while working. Damaged supply cords or extension cords present a risk of electric shock. c) Dirty or dusty power tools which have been used frequently for work on conductive materials should be checked at regular intervals at a Hilti Service Center. Under unfavorable circumstances, dampness or dust adhering to the surface of the power tool, especially dust from conductive materials, may present a risk of electric shock. d) When working outdoors with an electric tool check to ensure that the tool is connected to the electric supply by way of a ground fault circuit interrupter (RCD) with a rating of max. Use of a ground fault circuit interrupter reduces the risk of electric shock. e) Use of a ground fault circuit interrupter (RCD residual current device) with a maximum tripping current of 30 mA is recommended. Exposure to dust at a poorly ventilated workplace may result in damage to the health. 21 c) If the work involves breaking right through, take the appropriate safety measures at the opposite side. Parts breaking away could fall out and / or fall down and injure other persons. 5. 2. 5 Personal protective equipment tection, protective gloves and breathing protection while the power tool is in use. en The user and any other persons in the vicinity must wear suitable eye protection, a hard hat, ear pro- 6. Slide the side handle clamping band over the chuck and onto the cylindrical section at the front end of the power tool. 6. 2 Unlocking the tool (theft protection system) NOTE See section "Using the TPS theft protection system". 6. 3 Use of extension cords and generators or transformers Please refer to section 2 "Description". 6. 1 Fitting and adjusting the side handle 2 1. Operation 7. 1 Preparing for use CAUTION Wear protective gloves when changing insert tools as the insert tools get hot through use and they may have sharp edges. DANGER Always hold the power tool securely with both hands on the grips provided. Keep the grips dry, clean and free from oil and grease. 22 7. 1. 1 Fitting the insert tool 3 1. Check that the connection end of the insert tool is clean and lightly greased. Check that the sealing lip of the dust shield is clean and in good condition. Clean the dust shield if necessary or have it replaced if the sealing lip is damaged. Push the insert tool into the chuck and rotate it while applying slight pressure until it engages in the guide grooves. [. . . ] The electronic restart interlock is activated after an interruption in the electric supply. The power tool is too cold. No hammering action. The power tool doesn't start and the LED blinks red. The power tool doesn't start and the indicator lamp blinks yellow. The power tool doesn't achieve full power. A fault has occurred in the power tool. [. . . ]