User manual HILTI SFL 36

[. . . ] "The tool" referred to in these operating instructions is always the SFL rechargeable battery flashlight. Location of identification data on the tool The type designation and serial number can be found on the type plate on the tool. Make a note of this data in your operating instructions and always refer to it when making an enquiry to your Hilti representative or service department. Type: Serial no. : Operating controls ³ On / off switch Component parts Reflector Flashlight body Grip Battery Xenon light bulb for SFL 12/15; Krypton light bulb for SFL 18, SFL 24, SFL 36 Contents 1. [. . . ] exposed to the direct heat of the sun, on radiators, behind a motor vehicle windscreen or at a window. The battery cells may suffer damage if allowed to become completely discharged. 4. Technical data SFL12/15 SFL 18 SFL 24 SFL 36 Voltage 12 V / 15. 6 V 18V 24V 36V Light bulb Xenon 15. 6 V / 0. 7 A Krypton 18 V / 0. 65 A Krypton 18 V / 0. 65 A Krypton 18 V / 0. 65 A 5. Safety precautions In addition to the information relevant to safety given in each of the sections of these operating instructions, the following points must be strictly observed at all times. The tool must always be operated correctly, in accordance with the operating instructions and only when in a complete and undamaged state. Operation 7. 1 Switching the tool on Press the on / off switch for SFL12/15, SFL 18, SFL 24, SFL 36. 7. 2 Switching the tool off Press the on / off switch for SFL12/15, SFL 18, SFL 24, SFL 36. 7. 3 Pivoting the flashlight head SFL 12/15, SFL 18 The flashlight head can be pivoted up to 90°. Please note that the flashlight head can be pivoted only in one direction, i. e. Please note that the flashlight head can be pivoted only in one direction. Risk of dazzling: Do not direct the flashlight toward yourself or other persons. your Hilti customer service department or Hilti sales representative for further information. Should you wish to return the electric tool yourself to a disposal facility for recycling, proceed as follows: Dismantle the tool as far as possible without the need for special tools. Separate the individual parts as follows: Part / assembly Main material Recycling Outer casing 8. Care and maintenance 8. 1 Care of the tool The outer casing of the tool is manufactured from impactresistant plastic. Clean the outside of the tool at regular intervals with a slightly damp cloth. Do not use a spray cleaning system, high-pressure steam cleaning system or running water for cleaning. 8. 2 Care of the battery Keep the electrical contacts free from dust, oil and grease. In the event of battery capacity dropping below an acceptable level after a long period of use, we recommend that the battery is returned to Hilti for a diagnostic check. This could present a risk of fire in certain situations and may cause corrosive liquid to leak from the battery. 8. 3 Replacing the light bulb for SFL 12/15, SFL 18, SFL 24, SFL 36 Unscrew the reflector. Take the replacement bulb from its holder behind the reflector and insert it. [. . . ] Disposal Most of the materials from which Hilti power tools are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back your old electric tools for recycling. EC declaration of conformity Description: Designation: Year of design: Rechargeable battery flashlight SFL 12/15 - SFL18 SFL 24 SFL 36 2001 - 2002 2003 - 2004 We declare, under our sole responsibility, that this product complies with the following standards or standardization documents: 89/336/EWG, 73/23/EWG, EN 55 015, EN 60598-1, EN 60598-2-8 Hilti Corporation Dr. [. . . ]