User manual HILTI SF4000-A

[. . . ] SF 4000-A D GB F I NL P E DK SF N S GR Bedienungsanleitung Operating instructions Mode d'emploi 1­ 8 9­16 13­24 340750 *340750* 1 2 3 Click 4 5 6 7 8 9 10 11 12 13 14 15 L STOP R 16 SF 4000-A drywall screwdriver It is essential that the operating instructions are read before the tool is operated for the first time. Ensure that the operating instructions are with the tool when it is given to other persons. General information 1. 1 Indication of possible danger CAUTION In the text of these operating instructions, the word CAUTION is used to draw attention to a potentially dangerous situation which could lead to minor personal injury or damage to the equipment or other property. 1. 2 Pictograms Warning signs General warning Warning: electricity Warning: caustic substances Operating controls and components On / off switch (with electronic speed control) Forward / reverse switch Lockbutton for sustained operation Adjustable depth gauge (with bit change function) Screwdriver / accessory interface (click connection) 1 /4 chuck (for bit holder, magazine bit) Cooling air exit Rating plate Clutch system / gearing Scaffolding hook Belt hook Motor Grip Battery release button Motor cooling air intake Symbols Read the operating instructions before use. Waste material should be recycles. The desposal of batteries with general refuse is not permissible. These numbers refer to the corresponding illustrations. [. . . ] Incorrect initial charging may have a permanent, negative effect on battery capacity. Additional instructions ­ The tool may be used only with SFB 180 or SFB 185 batteries. ­ Never store batteries where they are exposed to the heat of the sun, on a radiator, behind a motor vehicle windscreen or at a window. Change to the second battery as soon as a drop in performance is noticed and recharge the battery immediately so that it is ready for re-use. When charging, always insert the battery directly in the charger G A caustic liquid may leak from defective batteries. In the event of contact with the skin, wash the area affected with soap and plenty of water. Should the liquid come into contact with the eyes, flush the eyes with water immediately and subsequently consult a doctor. 5. 2. 3 Requirements to be met by users G The tool is intended for professional use. G The tool may be operated, serviced and repaired only by authorised, trained personnel. This personnel must be informed of any special hazards that may be encountered. G Proceed carefully and do not use the tool if your full attention is not on the job. 5. 2. 4 Personal protective equipment G The operator and other persons in the immediate vicinity must always wear eye protection and breathing protection while the tool is in use. 7. Operation Setting the depth gauge (screwdriving depth) By adjusting the depth gauge, the screw can be driven flush, beneath the surface or left projecting. ­ Turn the depth gauge to the left = The screw is driven deeper I. ­ Turn the depth gauge to the right = The screw is driven less deeply II. Setting forward or reverse rotation The direction of rotation of the driving spindle can be selected by operating the forward / reverse push switch . An interlock prevents operation of the switch while the motor is running. ­ The drive spindle is then exposed and the tool can be used in reverse rotation for removing screws I. This also facilitates: ­ changing the bit or bit holder , ­ attaching the SMI55 magazine II, ­ re-tightening screws. 2. Position the depth gauge on the tool and press it in until it engages. Belt hook The belt hook can be used to attach the tool on a belt in a position close to the body. To achieve the optimal position, the belt hook must be pivoted 30° from the horizontal position, in an upwards direction . [. . . ] Disposal Most of the materials from which Hilti power tools are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back your old electric tools for recycling. Please ask your Hilti customer service department or Hilti sales representative for further information. [. . . ]