User manual HILTI SF150-A

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual HILTI SF150-A. We hope that this HILTI SF150-A user guide will be useful to you.


HILTI SF150-A : Download the complete user guide (534 Ko)

Manual abstract: user guide HILTI SF150-A

Detailed instructions for use are in the User's Guide.

[. . . ] of cells: Right of technical modifications reserved SFB150 15. 6 Volt 15. 6 Volt×2. 0 Ah = 31. 2 Wh 0. 89 kg yes nickel-cadmium Sub C design 13 SFB155 15. 6 Volt 15. 6 Volt×3. 0 Ah = 46. 8 Wh 0. 96 kg yes nickel-metal hydrid Sub C design 13 Applications Type of screw / application Size Speed Driving chipboard screws Driving wood screws into plastic anchors Driving self-drilling screws Drilling into softwood / particle board Drilling into with a hole saw Drilling into with a HSS twist-drill 8 8×80 mm dia. 13 mm dia. 1st (low) speed 1st (low) speed 2nd (high) speed 2nd (high) speed 1st (low) speed 2nd (high) speed 3. Safety precautions When using electric tools, the following fundamental safety precautions must always be observed in order to avoid the risk of injury, electric shock and fire hazards. Concealed electric cables or gas and water pipes present a serious hazard if damaged while you are working. [. . . ] When working, keep other persons outside the range of the tool you are using. Do not operate the tool in the vicinity of flammable liquids or gasses. Do not use it if it is damaged, incomplete or if the controls cannot be operated correctly. Ensure that the insert tools (drill bits, etc. ) are equipped with the appropriate connection end for the chuck system in use and that they are locked in position correctly in the chuck. Use only the recommended original Hilti accessories and auxiliary equipment. Use the tool only for the purposes for which it is intended (see page 8). Before use It is essential that the safety precautions printed in these operating instructions are read and observed before the tool is used. Before it is used for the first time, it is essential that a new battery is charged for 24 hours in normal charging mode or up to 12 hours using the conditioning charging mode, thus permitting "forming" of the battery cells to take place. At high temperatures: Do not store a battery where it may be subjected to high temperatures (e. g. exposed to the sun, at a window, behind a car windscreen or on a radiator). The cells can be damaged if the battery is completely discharged. Speed selection Two-speed switch The speed can be selected using the mechanical twospeed switch, i. e. Torque selection Torque clutch setting ring The release torque (2­12 Nm) is obtained by turning the setting ring to the desired torque level (setting 1­15). At the drilling symbol ( ), the torque clutch is blocked and the drill driver gives its max. Reversing switch The reversing switch is used to reverse the direction of rotation of the chuck. A locking device prevents operation of the switch while the motor is running. The control switch is deactivated when the reversing switch is in the central position. Speed control Switch with electronic speed control The speed can be controlled infinitely from zero to maximum by slowly depressing the switch. The side handle is adjustable and can be clamped in any disired position. Release the side handle by unscrewing the grip a few turns, bring it to the desired position and retighten the side handle. 5. Operation Insert tool insertion and removal Use the safety catch as protection against unintentional switching on during transport or when inserting or removing an insert tool. Quick-release chuck An insert tool can be clamped or released without a chuck key. When the drill driver is switched off by the on-off control switch, the spindle is locked. [. . . ] For repair or replacement, send tool and/or related parts immediately upon discovery of the defect to the address of the local Hilti marketing organization provided. This constitutes Hilti's entire obligation with regard to warranty and supersedes all prior or contemporaneous comments and oral or written agreements concerning warranties. 7. Accessories Battery removal Battery release button If the battery has to be changed, press in the two release buttons using two fingers and pull the battery out of the drill driver. Battery charging Only the Hilti SFC7/18 or TCU7/36 battery charger may be used. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE HILTI SF150-A




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual HILTI SF150-A will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.