User manual HILTI SDT25

[. . . ] The unit (electric screwdriver and decking tool) is used to drive the recommended metal construction screws in sheet metal. Decking tool for self-drilling screws with 10 mm metal washer (SDT 25) or with 15 mm metal washer (SDT 25-15). The working environment may be a construction site of any kind where metal construction work is taking place. The general safety precautions listed in the operating instructions must be observed. en 2. 2 Main applications / torque settings for the ST1800 / ST18 screwdriver SDT 25 Application Screw drilling capacity Screw type: Europe Torque setting Sheet metal / sheet metal Sheet metal / beam Application 2. 75 mm 5. 5 mm Screw drilling capacity S-MD 01 Z 4. 8×19 M S-MD 03 Z 5. 5×25 M Screw type: USA / Canada 6­8 8­10 Torque setting Sheet metal / sheet metal Sheet metal / sheet metal Sheet metal / sheet metal Sheet metal / beam Sheet metal / beam SDT 25-15 Application max. [. . . ] Do not wear loose clothing, loose long hair or jewelry as these can become caught up in moving parts. It is recommended that rubber gloves and shoes or boots with non-slip soles are worn when working outdoors. When working, keep other persons, particularly children, outside the range of the tool. To avoid tripping and falling when working, always lead the supply cord, extension cord and extraction hose away to the rear. Concealed electric cables or gas and water pipes present a serious hazard if damaged while you are working. Avoid contact between your body and earthed / grounded objects, such as pipes or radiators. External metal parts of the tool may become live, for example, when an electric cable is drilled into inadvertently. 5. 3. 1 Mechanical hazards 5. 3 General safety precautions Use the right electric tool for the job. Use The tool may jump back if released suddenly when under tension (pressed down), presenting a risk of injury (especially bruising). Take care when the nosepiece is under tension and the tool is turned upside down. The nosepiece may jump back suddenly, presenting a considerable risk of injury. Check that the insert tools used are compatible with the chuck system and that they are secured in the chuck or gear housing correctly. 9 02 BA SDT25/SDT2515 en 2. 4. 2004 10:19 Seite 10 en 5. 4 Requirements to be met by users The tool is intended for professional use. The tool may be operated, serviced and repaired only by authorized, trained personnel. This personnel must be informed of any special hazards that may be encountered. Proceed carefully and do not use the tool if your full attention is not on the job. 5. 5 Personal protective equipment The operator and other persons in the immediate vicinity must always wear eye protection and ear protection while the tool is in use. Wear eye protection Wear ear protection 6. Pull the clamping lever out to the front and rotate it to a position where it will not catch on things or get in the way. Pass the supply cord through the strain relief clasp on the grip on the right (feed a loop through from below and then pass it over the clip). Bring the magazine into position at the breach from behind and then engage it with the upper and lower tubular sections. 6. 1 Assembling the tool and electric screwdriver 6. 1. 1 Fitting the grips 1. Push the two grips into the lower tubular sections (the grip with the supply cord strain relief clasp on the right-hand side). In order to ensure that the grips can be clamped securely in position, the grips should not be extended beyond a length of 118 cm. Pull the clamping levers out to the front and rotate them into a position where they will not get caught on things (preferably pointing toward the inside). Set the ST 1800 or ST 18 to forward rotation (-NOTEScrews cannot be driven when the tool is set to the wrong direction of rotation). Guide the front end of the ST 1800 or ST 18 into the barrel of the main module. [. . . ] This means that only original Hilti consumables, components and spare parts may be used in the tool. This warranty provides the free-of-charge repair or replacement of defective parts only. Parts requiring repair or replacement as a result of normal wear and tear are not covered by this warranty. Additional claims are excluded, unless mandatory national rules prohibit such exclusion. [. . . ]