User manual HILTI SD4500

[. . . ] The power tools are intended for use on construction sites of all kinds for applications in the drywall installation and woodworking trades. Only the specified screwdriving bits, magazine and accessories should be used with the power tools. The general safety precautions listed in the operating instructions must be observed. en The SD 2500 is a hand-held, corded power tool for professional use in the woodworking and drywall installation trades. These power tools are used for driving and removing the recommended types of screws in the corresponding materials of the specified thickness. [. . . ] g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. c) Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool's operation. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. 5. 1. 5 Service a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. en 5. 2 Specific safety rules a) Hold power tools by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator. -WARNINGTo reduce the risk of injury, user must read instruction manual. en 6. Before use 6. 2 Use of a generator or transformer This tool may be powered by a generator or transformer which fulfils the following conditions: AC voltage, output power at least 2600 W. The operating voltage must be within +5 % and ­15 % of the rated voltage at all times. Never operate other tools or appliances from the generator or transformer at the same time. Switching other tools or appliances on and off may cause undervoltage and / or overvoltage peaks, resulting in damage to the power tool. -NOTEThe voltage provided by the electric supply must correspond to the information given on the type plate on the power tool. 6. 1 Using extension cords Use only extension cords of a type approved for the application and with conductors of adequate cross section. Failure to observe this point may cause the tool to loose power and the extension cord may overheat. Replace damaged extension cords. Recommended minimum conductor cross section and max. extension cord lengths: Mains voltage Conductor cross section 15 ft extension cord AWG AWG AWG 16 14 12 1. 23 1. 95 3. 09 25 ft 50 ft ­ 75 ft 100 ft ­ 100 ft 150 ft ­ 50 ft extension cord AWG AWG AWG 16 14 12 1. 23 1. 95 3. 09 25 ft 50 ft ­ 50 ft 75 ft ­ 100 ft 125 ft ­ Conductor cross section (mm2) 100 V 110­120 V 220­240 V 1. 5 ­ 20 m 50 m 2. 0 30 m 30 m ­ 2. 5 ­ 40 m 100 m 3. 3 50 m 50 m ­ 5 7. Operation 7. 5 Adjusting the depth gauge -NOTEBy adjusting the depth gauge, the screw can be driven flush with the surface or left projecting. [. . . ] This warranty is valid so long as the tool is operated and handled correctly, cleaned and serviced properly and in accordance with the Hilti Operating Instructions, and the technical system is maintained. This means that only original Hilti consumables, components and spare parts may be used in the tool. This warranty provides the free-of-charge repair or replacement of defective parts only over the entire lifespan of the tool. Parts requiring repair or replacement as a result of normal wear and tear are not covered by this warranty. [. . . ]