User manual HILTI PUA 80

[. . . ] aircfaft navigation systems) of b) Hjgh levels 0f radjatjon may cause interference to the PlVl 10. measurements sh0uld be to check lor correct operati0n. EMC (electromagnetic comoatibil!y) Although the Hrlti Pl\4 10 Jullils the section 6 of the operating Instructi0ns). Although the tool is designed I0r j0bsite use, like other opiical tools (bin0culars. it should be rviped dry belore being put av/ay in rts carryrng case. ThetoolshouldberepairedonlythroughHiltiservicecentres. Radiati0n inexcessofclass 2 may be emitted if the c0rrect procedures are nOt 0bserved when the casing is opened. [. . . ] Tbe balteries must be rnsulaled or removed before the tool is shipped. the tool and the llatleries must bedisposed 0f in accordance with the regulations applicable in the c0un1ry concerned. - Using and handling the PUA 80 Keep the t00l 0ut 0f reach 01 chrldren. aol \9' The PUA 80 Multrdirectional is a seltlevelling laser level thal proiects h0rizontal and vertrcal laser beams simultaneously. With a wavelength 0f 635 nm, the laser beams are easily visible and permit the instrument t0 be used at distances 01 up 10 and above 30 m, depending on lighting c0nditi0ns. 11 the tool cannol level itself aulomatically (floor inclination greater than t4"), the three beants begin to blink. Technical data Horizontal accuracy a1 25 C (77'F) <t 3Inm @10 m within self-levelling range 14' Vefiical accuracy al25'C (17"F) vrithin sel{-levelling ranqe I 4 (<t114 inch @ 60 feet) <t 3 mm @ 10 m (<t114 inch @ 60 feet) 90'angle accuracy aI25"C (/7'F) <r3mm@10m (<1/4 inch (@ 60 feet) (o @ SelI-levelling tinre: <5sec Sell-levellinq range in x and y. !4 Laser diode 625-640 nm, Poiryer <1mW Laser class 2 product Class ll ir' Levelling beams (horizontal) 2, P[rmb line beam 0N/0FF switch 0N indicator/low battery warning i5l Alignment/positioning notches i6 1 /4"-20 lhread f0r mounting or llrackel 0n a trip0d Light source: Laser class as per lECB25- 1 /EN60825 z Battery compartment for three type AA batteries 2] CFR: :8. Rubller housing Weight including batteries. 360g(08pounds) 30 D imensions. 50 mm x 108 mm x 95 nrm 3. ltems supplied Inslrumenl only (2"x43"x3. 75") Distance from edge of housing to centre of laser beam: Batte ries: 25 mm (1") AA alkaline or AA Ni/Cd (3 balreries) Battery lile with 3 AA alkaline llatteries vrith 3 Ni/Cd batreries. Approx 30 h Approx. 7h Automatic cut-out: 0perating temperature: Storage temperature. After approx. 20 minutes -20'C to 45'C (-4"F to -40 C to 63 C (-40 F 11 3'F) io 145 F) Insulation class: lP54 not including battery conr pa rtme nt I Sailcloth case Ptvl10 2 3. Target plate 0perating instructions 5 Point locator 32 Set 4. Working with the PM10 The insulating sticker must be removed {r0m the battery c0mpartmenl belOre the tool is operated for the lirst time. W'W'ffiffi' . M rll Sailcloth case t. . 2) . q. . A. Set up the t00l 0n a stable surface or supp0rt. a) 0n the Iloor b) 0n a tripod c) 0n the magnetic bracket the lrame clamp Activate the 0N/0FF switch and then wait until the laser sp0t stabilises itsell 0n the target (< 5s). d) 0n , qw, Wall bracket Frame clamp 7t 8, 1 lf the laser sp0t 0n the target begins to blink. the tool must be rep0siti0ned h0rizontally (begins to blink when 0utside the sell-levelling range ol I 4"). B. Pivot the tool through 90 (lhe laser beam still directed towards the ceiling). Set it up exactly 0n the cr0ss on the Jloor and again transler this mark to the ceiling. L'", # @1. , '' 44 4. 5. Repeat the instructions at paragraph 3 two more times. Four marks have now been made on the ceiling. Measured across the diagonal, the distance between these marks must not exceed 2 x 3 mm/10 m (2 centre. x 114"160 feet). lf this figure is exceeded, please contact your Hilti service T D t/z d2 w ;l 90' 90' Ma i ntenance Keep the three laser beam exil windows clean. Warranty Hilli v/arranls that the tool supplied is Iree of detects in material and workman-ship. This warranty is valid as long as the tool is 0perated and handled correctly, cleaned and serviced properly and in accordance with the Hilti 0perating Instructi0ns, all warranty claims are made within l2 months {rom the date 0f the sale (invoice date), and the technical system is maintarned. This means that only original Hilti consumables, c0mponents and spares may be used in the t001. This warranly provides the free-01-charge repair 0r replacenrent 01 delective pais only. Parts requiring repair or replacement as a result 0f normal wear and lear are not covered by thjs warranty. Additional claims are excluded, unless slringenl nali0nal rules prohibit such exclusi0n. In particular, Hilti is n0t 0bligated l0r direcl, indirecl, incidenlal or c0nsequenlial damages, losses 0r expenses in connection wilh, 0r by reason 01, the use of, or inabilily t0 use the t00l l0r any purp0se. lmplied warranlies 0l merchantability 0r fitness f0r a parlicular purpose are specilically excluded. [. . . ] In particular, Hilti is n0t 0bligated l0r direcl, indirecl, incidenlal or c0nsequenlial damages, losses 0r expenses in connection wilh, 0r by reason 01, the use of, or inabilily t0 use the t00l l0r any purp0se. lmplied warranlies 0l merchantability 0r fitness f0r a parlicular purpose are specilically excluded. send t00l and/or related parts immediately upon discovery 0f the defect to the address 0fthe lOcal Hiltr marketing organization provided. Thrs constitutes Hilti's entrre obligation with regard to warranty and supersedes all pri0r 0r c0fltemporane0us comments and oral or \, vritten agreements c0ncerning warranties. wind0w gently and dry it wilh a cl0th. [. . . ]