User manual HILTI PR16

[. . . ] PR 16 en Operating instructions *373165* 373165 80 0 Y X ³ 300 ¿ » · ´ +X 50 +Y ´ ² º ¶ ¾ PR 16 ¸ µ ¹ I +X +Y 0 50 300 80 1m X 30m Y 50 +Y +X 2m X 150m Y 50 +Y +X Y X 50 +Y +X A 20m 20m A 4mm B 20m 20m B B1 A1 A B B1 A A1 A2 x D1 B D2 B1 B2 A A1 It is essential to read these operating instructions carefully before operating the laser for the first time. The operating instructions should always be with the laser when it is given to other persons. Laser components PR 16 Rotating Laser 1. , , Inclination/direction" button (activates the servo motors in the X/Y inclination/direction 17. General Information 1. 1 Headings indicating danger CAUTION Used to indicate a potentially dangerous situation that could lead to minor personal injuries or serious damage to property or the environment. [. . . ] The laser begins to rotate automatically at the last speed selected (indicated by LED). 6. 2 LEDs for operating status and battery voltage Green (continuous) - Laser ready for operation (shock warning system activated; when laser has neither been shifted and nor readjusted for 1 minute) Green (blinking) battery voltage low Red (continuous) batteries discharged; laser beam off All LEDs and the laser blink if the laser is knocked. 16 6. The line thus indicates the reference accurately at any required point in the plane of alignment. + Cancelling Smart Scan function Hold beam catcher in the laser plane again. Operation 7. 4 Working with the laser detector (accessory) For distances of up to 150m or unfavourable light conditions, the detector (PA 350; available as an accessory) can be used. Shortly before levelling is achieved, the laser beam will switch on and rotate (in last mode selected). Depending on the application, stand the laser on, for example, a level surface and level it approximately with the foot screws (with the aid of the spirit level). The X-LED will show green = X-axis is automatically perpendicular and is monitored. The Y-LED will show red = Y-axis can be aligned manually with the servo buttons (laser plane remains perpendicular). 21 7. Operation 7. 6. 1 Inclination/Axis button Used to manually align the X-axis as well (X-LED will change to red). If the manual mode is chosen for the Xaxis and the Y-axis, the laser will no longer be monitored to ensure it remains perpendicular. The Inclination/Axis button can be pressed again to toggle between X- and Yaxes as necessary. The laser has to be switched off and on again to return to the original mode (X-LED = green; Y=LED = red). NOTE If manual (X- and/or Y-) axis setting was the last mode used, within 3 seconds of switching the laser on the Inclination/Axis button can be pressed to retain the last setting. Otherwise the laser will automatically return to the standard mode (X-LED = green; Y-LED = red). 22 7. Shortly before levelling is completed, the laser beam will be switched on and rotate (in the last mode selected). 7. 7. 1 Inclination/Axis button Used to set the inclination of the X- or Y-axis manually (X- or Y-LED will change to red). If the manual mode is selected for the X- and Y-axes, the laser is no longer monitored to ensure it remains level. The Inclination/Axis button can be pressed again to toggle between X- and Y-axes as necessary. The laser has to be switched off and on again to return to the original mode (X-LED = green; Y-LED = green). NOTE If manual (X- and/or Y-) axis setting was the last mode used, within 3 seconds of switching the laser on the Inclination/Axis button can be pressed to confirm that the last setting should be retained. Otherwise the laser will automatically return to the standard mode (X-LED = green; Y-LED = red). 23 8. [. . . ] Most of the materials from which Hilti tools are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back old tools for recycling. Please ask your Hilti customer service department or Hilti representative for further information. 30 10. [. . . ]