User manual HILTI PP10

[. . . ] 00_Cover_PP_10_11_P2. qxd 23. 1. 2006 09:14 Seite 1 10 11 Hilti Corporation LI-9494 Schaan Tel. : +423 / 234 21 11 Fax: +423 / 234 29 65 www. hilti. com PP 10/11 Operating instructions Bruksanvisning Brugsanvisning en sv da 12 Hilti = registered trademark of Hilti Corp. , Schaan W 3117 0106 00-Pos. & O. 1 Printed in Liechtenstein © 2006 233821 / A 233821 *233821* 00_Cover_PP_10_11_P2. qxd 23. 1. 2006 09:14 Seite 5 1 2 3 6 7 4 5 8 9 PP 10 / 11 pipe laser It is essential that the operating instructions are read before the tool is operated for the first time. Ensure that the operating instructions are with the tool when it is given to other persons. Contents Page 1 General information 1 2 Description 2 3 Accessories 3 4 Technical data 3 5 Safety rules 4 6 Before use 5 7 Operation 7 8 Care and maintenance 10 9 Troubleshooting 11 10 Disposal 11 11 Warranty 12 12 FCC statement (applicable in US) / IC statement (applicable in Canada) 12 13 EC declaration of conformity 13 Component parts 1 PP 10/11 pipe laser ; Warning / standby LED = Control panel % Display & Grip ( Grip mount ) PPA 84 cable connector + Battery compartment cover lock § PPA 82 battery incl. mains adaptor / Plumb spot PP 10 / 11 pipe laser : Laser exit window · Remote control signal receiving window $ Plumb spot £ Pivot point mark Control panel | Direction control button / auto centering ¡ Plumb spot ON button Q Laser beam mode button W Remote control signal receiving window E Lock button R Target plate auto-centering button (only with the PP 11) T Direction control button / auto centering Z SET button U Laser beam up / down, value-entry button I Warning / standby LED O Laser beam up / down, value-entry button P ON / OFF button en @ Remote control signal receiving window 1. [. . . ] Rotate the laser tool in the direction of the arrow shown in the display. 7. 4 Switching the tool on Press the ON / OFF button. NOTE The PP 10 / 11 is capable of leveling itself within a range of +/- 10%. The tool levels itself automatically when set up within this range. The LED begins to blink when the inclination of the tool is more than +/- 7 10% from the set inclination. The tool should then be tilted in the direction indicated by the arrow. 7. 5 Setting the inclination 7 Inclination can be set either manually or automatically. Inclination can be set within the -15% to +40% range (for inclination of over 10%, the adaptor or some other aid should be used to provide initial inclination of the laser tool). Press the right-hand direction control button in order to reach the correct position (the left direction control button can be used to move back). Press the right-hand direction control button to move to the next position. 7. 5. 2 Manual entry of inclination NOTE Inclination can also be set directly by moving the laser beam. The value indicated becomes higher or lower as the laser beam is moved. Press the laser beam UP and DOWN buttons at the same time to move the laser beam to the zero position. 7. 6 Aligning the target line 6 Use the direction control buttons on the PP 10 / 11 or PPA 20 remote control unit to move the laser beam horizontally to the right or left. 8 7. 7 Beam position indicator 6 1 2 3 Beam position indicator End position left End position right en 7. 8 Adjusting the position of the beam 6 The maximum lateral adjustment range is 9m at a distance of 30m. The current position of the beam can be read from the display at any time. 7. 8. 1 Adjusting the beam end position left / right The display informs the operator when the beam has reached the left or right end position and cannot be moved further. If this position is reached frequently it is recommended that the tool is pivoted slightly to the left or right and the beam then realigned. 7. 9 Automatic centering Press both direction control buttons (left and right) at the same time to center the laser beam automatically. 7. 10 Target plate auto-centering (only PP 11) 8 NOTE This feature is particularly useful for setting up the laser tool the next working day. Set up the target plate with the reflective stripes facing the laser tool. The laser then finds the horizontal center of the target plate automatically. 7. 11 Display while searching 1 The tool has not yet completed the self-leveling procedure. The display indicates stabilization of the laser beam after selfleveling. NOTE The display indicates that searching (auto centering) is in progress. [. . . ] only genuine Hilti consumables, accessories and spare parts are used with the product. This warranty provides the free-of-charge repair or replacement of defective parts only. Parts requiring repair or replacement as a result of normal wear and tear are not covered by this warranty. Additional claims are excluded, unless mandatory national regulations prohibit such exclusion. [. . . ]