User manual HILTI PMP34

[. . . ] PMP 34 Bedienungsanleitung Operating instructions Mode d'emploi Istruzioni d'uso Gebruiksaanwijzing Manual de instruções Manual de instrucciones de en fr it nl pt es el zh ja ko 286153 *286153* 90 90 BA_PMP34_en. qxd 22. 11. 2004 12:49 Uhr Seite 1 PMP 34 point laser It is essential that the operating instructions are read before the tool is operated for the first time. Ensure that the operating instructions are with the tool when it is given to other persons. Component parts Pendulum lockbutton Selector button LED indicator Reference line Pendulum Base Mounting slot 1. General information 1. 1 Safety notices and their meaning -CAUTIONUsed to draw attention to a potentially dangerous situation which could lead to minor personal injury or damage to the equipment or other property. -NOTEUsed to draw attention to an instruction or other useful information. [. . . ] The tool and the batteries must be disposed of in accordance with national regulations in order to avoid environmental pollution. Consult the manufacturer if you are unsure. 4 BA_PMP34_en. qxd 22. 11. 2004 12:49 Uhr Seite 5 6. Operation & applications 7. 1. 3 Switching the tool/laser beams off 1. Press the selector button repeatedly (1-3 times depending on previous operating mode) until the laser beam is no longer visible and the LED no longer lights. -NOTEThe pendulum is locked when the tool is in the closed position (laser beam blinks). Bring the reference line into alignment with (parallel to) the top edge of the base section. -NOTEThe pendulum is able to swing freely when the reference line is parallel to the base section, when the pendulum lockbutton is not pressed in and when the tool is set up in a horizontal position ( ± 5°). The laser beams blink rapidly when the tool is unable to level itself automatically. 7. 1. 2 Switching on the laser beams Switching on only the plumb beams (vertically upwards and downwards): 1. -NOTEThe tool will be switched off when the selector button is pressed (between one and three times, depending on operating mode) or when the batteries are exhausted. 20 cm from the wall (B) with the laser beam directed toward the wall (B). Mark the position of the center (3) of the laser beam on the wall (B) with a cross. Pivot the tool through 180° and mark the center of the laser beam (4) on the opposite wall (A) with a cross. ­ If the reference points 1 and 3 are located on different sides of the mid point (see example), then subtract d2 from d1. ­ If the reference points 1 and 3 are located on the same side of the mid point, then add d1 and d2 together. Divide the result by twice the length of the room (room length x 2). The result provided by this formula refers to the tool's accuracy in mm at 10 m (formula (1)). This result should be within the specification for the tool (3 mm at 10 m). 6 BA_PMP34_en. qxd 22. 11. 2004 12:49 Uhr Seite 7 The maximum permissible error is 3 mm at 10 m. Now position the tool with the lower plumb beam exactly on the center of the reference cross so that the front beam strikes exactly the center of target plate 1. Mark the position (d1) of the perpendicular beam with a target plate at a distance of 5 m (fix the target plate in position). The lower plumb beam must remain in the center of the reference cross. The perpendicular beam must strike target plate 2 exactly in the center (cross-hairs). [. . . ] Warranty Hilti warrants that the tool supplied is free of defects in material and workmanship. This warranty is valid as long as the tool is operated and handled correctly, cleaned and serviced properly and in accordance with the Hilti operating instructions, all warranty claims are made within 12 months (unless other mandatory national regulations prescribe a longer minimum period) from the date of sale (invoice date) and the technical system is maintained, i. e. only genuine Hilti consumables, accessories and spare parts are used with the product. This warranty provides the free-of-charge repair or replacement of defective parts only. [. . . ]