User manual HILTI PMP32

[. . . ] Features: Upward beam accuracy (± 3 mm at 10 m on a leveled surface). "Out of level" warning signal when the self-leveling range is exceeded (the laser beams blink). Automatic cut-out: The tool switches itself off automatically after 15 minutes. 2. 1 Items supplied with the point laser (cardboard box version) 1 PMP 32 plumb laser 1 soft pouch 4 batteries 1 operating instructions 2 target plates en 3. [. . . ] Nevertheless, as with the sun, one should not look directly into sources of bright light. Do not direct the laser beam toward persons. 6 Laser warning plate based on IEC825/EN 60825-01:2003: 1/4 s 2 Laser warning plate for the USA based on CFR 21 § 1040 (FDA): LASER RADIATION - DO NOT STARE INTO BEAM en 620-690nm/0. 95mW max. CLASS II LASER PRODUCT This laser product complies with CFR 21 § 1040 (FDA) as applicable. 5. 5 General safety precautions Check the tool for possible damage or dirt before use. If the tool is found to be damaged, have it repaired at a Hilti service center. The accuracy of the tool must be checked after it has been dropped or subjected to other mechanical stresses. When the tool is brought into a warm environment from very cold conditions, or vice-versa, allow it to become acclimatized before use. If mounting on an adaptor, ensure that the tool is attached securely. Although the tool is designed for the tough conditions of jobsite use, as with other optical instruments (binoculars, spectacles, cameras) it should be treated with care. Although the tool is protected to prevent entry of dampness, it should be wiped dry each time before being put away in its Hilti toolbox. 5. 5. 1 Electrical hazards The batteries must be insulated or removed from the tool before it is shipped. The tool and the batteries must be disposed of in accordance with national regulations in order to avoid environmental pollution. Before use en 6. 1 Inserting new batteries -NOTEDo not use damaged batteries. Operation & applications 7. 1 Operation -NOTEThe pendulum is able to swing freely when the tool is set up in a horizontal position ( ± 4°). The laser beams blink rapidly when the tool is unable to level itself automatically. 7. 1. 1 Switching on the laser beams Switching on the plumb beams (vertically upwards and downwards): 1. 4 seconds) until the LED on the tool blinks three times in confirmation. -NOTEThe tool will be switched off when the selector button is pressed or when the batteries are exhausted. 7. 2 Examples of applications 7. 2. 1 Vertical alignment (plumbing) of sections of a steel structure 7. 2. 2 Aligning pipe fastenings 7. 2. 3 Vertical alignment (plumbing) of an elevator rail 7. 3 Operating status indicators 7. 3. 1 LED The LED doesn't light. The tool is switched off. The LED blinks. The laser beam is switched on. The tool is in operation. The batteries are almost exhausted. The temperature of the tool is above 40 °C (104 °F) or below ­10 °C (14 °F) (no laser beam projected). The laser beam blinks rapidly. The batteries are almost exhausted. The tool cannot level itself en automatically. 8. Mark the position of the vertical beam on the ceiling (attach a piece of paper to the ceiling). Repeat the procedure after pivoting the tool through 180° and 270°. [. . . ] This equipment generates, uses and may radiate radio frequency energy. Accordingly, if not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by taking the following measures: ­ Reorient or relocate the receiving antenna. [. . . ]