User manual HILTI PML32-R

[. . . ] 8 PML 32 / PML 32-R Hilti Corporation LI-9494 Schaan Tel. : +423 / 234 21 11 Fax: +423 / 234 29 65 www. hilti. com Bedienungsanleitung Operating instructions Mode d'emploi Istruzioni d'uso Manual de instrucciones Gebruiksaanwijzing de en fr it es nl 9 Hilti = registered trademark of Hilti Corp. , Schaan W 2765 0906 00-Pos. 1 1 Printed in Liechtenstein © 2006 Right of technical and programme changes reserved S. & O. 377394 / E 377394 *377394* 1 2 6 3 4 5 7 It is essential that the operating instructions are read before the tool is operated for the first time. Ensure that the operating instructions are with the tool when it is given to other persons. Component parts 1. [. . . ] Safety precautions 5. 3. 1 Electromagnetic compatibility Although the tool complies with the strict requirements of the relevant directives, Hilti cannot entirely rule out the following possibilities: ­ The tool may cause interference to other equipment (e. g. ­ The tool may be subject to interference caused by powerful radiation, which may lead to incorrect operation. Check the accuracy of the tool by taking measurements by other means when working under such conditions or if you are unsure. 5. 3. 2 Laser classification The tool conforms to laser class 2 based on the IEC825-1 / EN60825-01 standard and class II based on CFR 21 § 1040 (FDA). The eyelid closure reflex protects the eyes when a person looks into the beam unintentionally for a brief moment. Nevertheless, the eyelid closure reflex may be negatively affected by medicines, alcohol or drugs. Nevertheless, as with the sun, one should not look directly into sources of bright light. Safety precautions Laser information plates for the USA based on CFR 21 § 1040 (FDA): This laser product complies with 21 CFR 1040, as applicable. 5. 4 General safety precautions ­ Check the tool for possible damage before use. If it is found to be damaged, have it repaired at a Hilti service centre. ­ The accuracy of the tool must be checked after it has been dropped or subjected to other mechanical stresses. ­ When the tool is brought into a warm environment from very cold conditions, or vice-versa, allow it to become acclimatized before use. ­ If mounting on an adaptor, ensure that the tool is screwed on securely. ­ Although the tool is designed for the tough conditions of jobsite use, as with other optical instruments (binoculars, spectacles, cameras) it should be treated with care. 12 5. Safety precautions ­ Although the tool is protected to prevent entry of dampness, it should be wiped dry each time before being put away in its transport container. 5. 4. 1 Electrical hazards ­ The batteries must be insulated or removed from the tool before it is shipped. ­ The tool and the batteries must be disposed of in accordance with national regulations in order to avoid environmental pollution. Operation 6. 1 Inserting new batteries -NOTEDo not use damaged batteries. -CAUTIONTake care to observe correct polarity when inserting the batteries. Operation -NOTEThe pendulum is locked when the tool is in the closed position (laser beam blinks). Bring the reference line into alignment with (parallel to) the top edge of the base section. -NOTEThe pendulum is able to swing freely when the reference line is parallel to the base section, when the pendulum lockbutton is not pressed in and when the tool is set up in a horizontal position ( ± 5°). [. . . ] Ask Hilti customer service or your Hilti representative for further information. 29 11. Disposal Dispose of batteries in accordance with national regulations Only for EU countries Disposal of electric tools together with household waste is not permissible!In observance of European Directive 2002/96/EC on waste electrical and electronic equipment and its implementation in accordance with national law, electric tools that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility. 30 12. Manufacturer's warranty ­ tools Hilti warrants that the tool supplied is free of defects in material and workmanship. [. . . ]