User manual HILTI PD-30

[. . . ] PD 30 en Operating instructions *372204* 000000 5 2 9 10 9 7 10 4 8 6 31 PDA 50 PDA 80 PDA 60 PDA 81 PDA 61 PDAW 80-1 PDA 62 PDAW 80 / 81-1 PDA 70 PDAW 80 / 81-2 PA 970 PDAW 80 / 81-3 PDAW 81-1 PD 30 laser range meter It is essential that the operating instructions are read before the range meter is used the first time. Ensure that the operating instructions are with the range meter when it is given to other persons. Contents Contents 1. 6 PDAW 80 / 81-2 car battery plug 6 PDAW 80 / 81-1 charging adaptor 6 PDAW 80 / 81-3 battery pack. 9 Component parts Laser exit aperture Control panel Receiving lens Plastic casing Horizontal bubble Battery compartment Folding spike Graphic display of operating status Metal contact points for precise measurement (3x rear) Metal supports for precise measurement (3x underneath) Optical sight 2. [. . . ] 7. 3 Measuring distances Distance measurements can be taken to all "non-cooperating" stationary targets, i. e. concrete, rock, wood, plastic, paper, etc. , The use of prisms or other strongly reflecting targets is not permitted and, if used, might falsify the results. 7. 3. 1 Measuring references = switch key The range meter can measure distances from three different measuring reference points. By pressing the "switch" key on the left at the front of the range meter the measuring reference point toggles between front edge and rear edge. If the spike is folded out 90°, the reference position is set to the end of the spike. Display Reference position Front edge Rear edge End of spike 15 - NOTE ­ If the spike is folded out 180°, reference point is always automatically set to the rear edge. 7. 3. 2 Measuring distances step by step The range meter measures distances in a very short time and, when doing so, shows various information in the display. This switches on the red laser beam which is visible as a laser spot on the target surface. Press the "Measure" key once again to measure the distance. 7. Operation The result appears in the result line normally in less than a second. Generally, the measured distance will be completed in less than a second and shown in the result line the display. - NOTE Alternatively the range meter may be switched on by pressing the On key and the laser then activated by pressing the measure key. 7. 3. 3. 2 Continuous measurement Press the "Measure" key for about 2 seconds to activate this measuring mode. When doing so, it does not matter whether or not the range meter is off or the laser beam is switched on or off. During continuous measurement, the distances are updated in the result line by about 8 to 15 measurements every second. If the beep signal is switched on, continuous measurement is indicated by a Beep. The measuring process is stopped by pressing the "Measure" key once again. On doing so, the last valid distance measurement shows in the result line on the display. - NOTE Continuous measurement is possible wherever distances can be measured. This applies also to functions, such as areas, volumes and Pythagoras. If further measurements are taken, up to three previously determined distances are shown in the intermediate result lines, i. e. a total of the last four measured distances are shown. 7. 3. 3 Measuring mode Two different measuring modes are available to measure distances. These are single distance measurement and continuous distance measurement. [. . . ] Ask the Hilti customer service or your local Hilti representative for further information. Should you wish to return a range meter, etc. , to a disposal facility yourself for recycling, dismantle it as far as this is possible without the need for special tools. Separate the individual parts as follows: Part / assembly Casing Main material Plastic Recycling as Plastic / scrap metal Plastic scrap metal Electronics scrap * Plastic scrap Switch Plastic Screws / small parts Steel, aluminium, magnets Electronics Various (Re-chargeable) Alkali manganes batteries, carrying case* woven synthetic fabric - NOTE Always remove the batteries before shipment. 24 * Dispose of batteries in accordance with national regulations 12. Warranty Hilti warrants that the product supplied is free of defects in material and workmanship. [. . . ]