User manual HILTI GX120-ME

[. . . ] GX120-ME Hilti Corporation LI-9494 Schaan Tel. : +423 / 234 21 11 Fax: +423 / 234 29 65 www. hilti. com Operating instructions Mode d'emploi Manual de instrucciones Istruzioni d'uso Brugsanvisning Bruksanvisning Bruksanvisning Käyttöohje Manual de instruções Kasutusjuhend en fr es it da no sv fi pt el et zh Hilti = registered trademark of Hilti Corp. , Schaan W 3410 0507 2-Pos. 1 1 Printed in Liechtenstein © 2007 Right of technical and programme changes reserved S. & O. 39199 / A 39199 *39199* 1 5 2 +Ç 1 8 9 +" + +# 7 3 +± +[ 6 Gas 4 5 2 3 1 3 2 1 3 2 4 5 1 2 4 +[ 3 GAS 6 7 6 4 5 2 3 8 9 1 1 1 3 2 2 10 11 + 12 13 1 1 2 2 1 3 14 15 1 3 2 +" 16 17 GX 120ME gas-driven fastening tool It is essential that the operating instructions are read before the tool is operated for the first time. Ensure that the operating instructions are with the tool when it is given to other persons. Contents 1. [. . . ] c) In case of unconsciousness: Bring the person affected into a secure recovery position. 7. 1 Operation 6 NOTE It is possible to drive a fastener only when more than 3 nails are in the magazine. Position the nose of the tool at right angles to the working surface and then press it against the working surface as far as it will go. After driving the fastener, lift the tool away completely from the working surface. 7. 1. 1 Using pipe rings and other fasteners If you wish to use pipe rings and other types of fastener, push the plastic part of the fastener into the tool nosepiece. 7. 2 Gas level indicator 5 Please refer to section 6. 4 "Checking the gas can (for 2 seconds)". 7. 3 Fitting and removing the magazine 7. 3. 1 Removing the magazine 7 1. Push the locking lever down toward the magazine. NOTE When holding the tool steady with the second hand, the hand must be positioned in such a way that no ventilation slots or openings are covered. WARNING Material may splinter when the fastener is driven or fragments of the magazine strip may fly off. Wear protective glasses and a hard hat (tool operator and bystanders). CAUTION The fastener is driven by the energy released on ignition of a gasair mixture. WARNING Never make the tool ready to fire by pressing it against a part of the body (e. g. When the tool is ready to fire, fasteners could be driven inadvertently into parts of the body. WARNING Never pull the tool nosepiece back by the fastening component inserted in it (e. g. Guide the magazine toward the tool until the shaped parts fit together. 7. 4. 2 Settings at the nosepiece NOTE When the power regulator is set to "+", the nosepiece is set to the standard fastener driving depth. NOTE When the power regulator is set to "", the nosepiece is set to the reduced fastener driving depth. NOTE If the nail is still driven too deeply when the power regulator is set to "", it may be necessary to use a longer nail. 7. 4. 2. 1 Setting the standard fastener driving depth 10 Set the power regulator to "+". 7. 4. 2. 2 Setting the reduced fastener driving depth 10 NOTE This setting is suitable for fastening thin sheet metal to soft materials (e. g. 7. 4. 3 Fitting the tool nosepiece 11 WARNING Check to ensure that the tool is not loaded. The tool could be made ready to fire inadvertently by pressing the nosepiece in by hand. 1. [. . . ] The fastener driving rate was considerably higher than 1200 per hour and the gas can is almost empty. 12 Fault The tool doesn't fire or fires sporadically. Possible cause Operation outside the limits of permissible ambient conditions. Remedy Adjust the ambient conditions as far as possible (e. g. In very cold conditions (10°C), allow the tool to warm up together with the gas can (e. g. Take care to ensure that the tool is lifted away completely from the working surface after driving each fastener. Fit the tool nosepiece into the support supplied and use the pin punch to remove the fastener. [. . . ]