User manual HILTI DX460

[. . . ] DX460 en Operating instructions 1­17 371665 *371665* 1 3 2 1 0 46 DX 6 45 7 8 9 10 11 15 MX 72 20 13 14 15 16 19 17 18 12 21 14 15 X-460-F810SS 6. 2 X-460-F8N15 X-460-F8N10 X-460-F8S12 X-460-F8SS X-460-F10 XMX72 X-460-F8 X-DNI X-ZF X-SL X-EDNI X-CR X-DAK X-AL-H X-FS X-SW X-M8/X-W8 . . . P10 X-IE X-IE / XI-FV S = X-460-P8 W = X-460-P8W AL = X-460-P8AL 10 = X-460-P10 IE = X-460-PIE IE-L = X-460-PIE-L S/W S/W S/W S S S/W S/W S/W S/W S/W S S S AL S/W S/W S S S/W S/W S/W S S S AL S/W S/W S/W S S S AL S S S 10 10 IE IE-L X-460-FIE X-460-FIE-L 6. 1 1 7. 1 1 7. 7 1 4 1 2 3 2 5 7. 2 2 7. 8 6. 3 3 3 1 2 7. 9 4 7. 3 5 7. 10 90 6 7. 4 1 2 7. 11 7 7. 5 8 1 4 2 3 5 7. 12 90 7. 6 8. 3 1 1 8. 6 1 2 3 2 4 3 2 4 8. 7 1 1 2 2 5 8. 8 2 1 8. 4 8. 9 8. 10 1 2 8. 5 8. 11 8. 12 8. 13 2 3 1 CLICK 8. 14 1 9. 1 2 1 2 2 3 4 3 4 DX 460 powder-actuated tool It is essential that the operating instructions are read before the tool is operated for the first time. Ensure that the operating instructions are with the tool when it is given to other persons. Description of main parts @ Exhaust gas piston return unit ; Guide sleeve = Housing % Cartridge guideway & Power regulation wheel release button ( Power regulation wheel ) Trigger + Grip § Piston return unit release button / Ventilation slots : Piston rings · Piston * $ Fastener guide * £ Fastener guide release button | Buffer * ¡ Magazine * Q Magazine cover W Magazine cover release button E Magazine release button R Load status indicator T Replaceable fastener guide nosepiece * * These parts may be replaced by the user/operator. 1. [. . . ] s Wear safety goggles and a hard hat (users and bystanders). C d Steel A = min. base material thickness = 4 mm ( 5/32") X-EDNI nail (steel) Threaded studs for concrete or steel CAUTION s The nail or stud is driven by a cartridge being fired. s Wear ear protection (users and bystanders). SD ET SL MD Penetration depth (ET) 12 ± 2 mm + material thickness (MD) = shank length (SL) min. 4 mm B Penetration depth concrete: 27± 5 mm steel: 12±2 mm A ET C WARNING s The tool could be made ready to fire if pressed against a part of the body (e. g. s Never press the muzzle of the tool against parts of the body. Concrete A = min. base material thickness = 100 mm (4") X-DNI nail (concrete/steel) ET SL MD SD ET SL MD WARNING s Under certain circumstances, the tool could be made ready to fire by pulling back the magazine, fastener guide or the fastener by hand. s When in the "ready to fire" state, a fastener could be driven into a part of the body. s Never pull back the magazine, fastener guide or fastener by hand. Length of nail for concrete Penetration depth (ET) 27± 5 mm + material thickness (MD) = shank length Length of nails for steel Penetration depth (ET) 22± 5 mm (nail point must protrude) + material thickness (MD) = shank length steel thickness (SD) = min. 10 mm X-IE fastener (concrete, solid rendered masonry, steel) On all base materials, fastener length corresponds to thickness of insulating material. 7 aa Loading the single-fastener tool 7. 1 1. Insert the fastener (head first) until the washer is held in the tool. Load the cartridge strip (narrow end first) by inserting it into the bottom of the tool grip until flush. If the strip has been partly used, pull it through until a live cartridge is in the chamber. (The last visible number on the back of the cartridge strip indicates which cartridge is next to be fired. ) aa Adjusting the driving power 7. 2 Start with the lowest cartridge power level and the tool set at the lowest power setting. If the fastener doesn't penetrate deeply enough, increase the power level and repeat steps 1 to 3. WARNING q Never attempt to drive a fastener in an existing hole except where recommended by Hilti, e. g. aa Reloading the single-fastener tool 7. 4 Ensure that no cartridge strip or fastener is loaded in the tool. Remove the cartridge strip by pulling it upwards out of the tool and remove the fastener from the fastener guide. Load the cartridge strip (narrow end first) by pushing it into the grip from below until flush. If the strip has been partly used, pull it through until an unused cartridge is in the chamber. (The last visible number on the back of the cartridge strip indicates which cartridge is next to be fired. ) When the indicator shows red, or partly red, there are 3 or less nails in the magazine. A strip of 10 nails may be loaded. WARNING q All nails in the magazine must be of the same length. WARNING q Never attempt to drive a fastener in an existing hole except where recommended by Hilti, e. g. [. . . ] S12 15 Fastening on steel Damaged nail head Cause s Driving power too high s Wrong piston used s Worn-out piston Possible remedies s Reduce power setting s Use lighter cartridge s Check nail/piston combination s Change piston 10. Disposal Most of the materials from which Hilti power actuated tools are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back your old powder actuated tools for recycling. [. . . ]