User manual HILTI DD200

[. . . ] DD 200 Bedienungsanleitung Operating instructions Mode d'emploi Istruzioni d'uso Gebruiksaanwijzing Manual de instruções Manual de instrucciones de en fr it nl pt es el 305560 *305560* 1 2 4 8 11 12 9 32 13 14 31 22 23 3 28 26 7 9 14 15 28 39 18 41 42 40 17 43 16 19 29 29 27 24 25 5 6 34 10 21 33 38 37 36 35 30 20 2 3 3 2 2 1/3 1 1 4 4/6 2 5 5 6 2 5 1/12 56 1 3 3 7 4 3 2 2 10 9 8 11 6 8 6 7 3/5 1/3 2 4 1 2 4 1/3 8 2 1 3 9 3 2/4 1 5 10 3 2/4 11 5 1 5 1/3 4 6 2 12 13 1 2 2/4 3 1 14 6 2 4/5 3 15 6 2 4/5 3 1 1 16 8 4 6/7 5 17 4 3 5 2 2 6 1 1 3 18 2 19 3/4/6 1 1/3 2 5 DD 200 diamond core drilling system It is essential that the operating instructions are read before the machine is operated for the first time. Ensure that the operating instructions are with the machine when it is given to other persons. Operating controls, parts and indicators Drilling rig (drive unit and drill stand) Drive unit ; Service indicator = Drilling performance indicator % On / off switch & Gear selector switch ( Water flow regulator ) Chuck + Supply cord with PRCD § Carrying grips (2) / Water hose connector : Type plate · Interface Drill stand $ Column £ End cap | Strut ¡ Base plate Q Clamping spindle W Clamping nut E Anchor R Leveling screws T Hole center indicator Z Carriage U Drive unit (eccentric) locking bolt I Direct drive O Reduction gear P Carriage locking mechanism Ü Hand wheel [ Carrying grip ] Supply cord guide Æ Type plate º Leveling indicators (2) · End stop A Wheel assembly mounting point ACCESSORIES Vacuum base plate S Pressure gauge D Vacuum release valve F Vacuum seal G Vacuum hose connector H Wheel assembly mounting point Water flow indicator J Water flow indicator Water collector system K Water collector holder L Water collector Ö Seal Ä Seal Column extension Eccentric bolt Depth gauge Spacer OE Drive unit locking mechanism Wheel assembly Å Set of wheels Page 15 17 17 17 18 20 23 25 26 27 28 28 en Contents 1. General information 1. 1 Safety notices and their meaning -DANGERDraws attention to imminent danger that could lead to serious bodily injury or fatality. -CAUTIONDraws attention to a potentially dangerous situation that could lead to slight personal injury or damage to the equipment or other property. [. . . ] Lock the carriage in position on the column (activate the carriage locking mechanism). 6. 3. 9 Mounting the drive unit on the drill stand -NOTEEnsure that the drive unit is disconnected from the electric supply. Lock the carriage in position on the column (activate the carriage locking mechanism). Push the locking bolt into the carriage or spacer as far as it will go. Clip the supply cord into the supply cord guide on the carriage cover. -NOTEA water flow indicator (accessory) can be connected between the water supply hose and the hose connector on the drive unit. -CAUTIONCheck the hoses for damage at regular intervals and ensure that the maximum permissible water supply pressure of 6 bar is not exceeded. 6. 3. 11 Fitting the water collector system (accessory) -NOTEUse of the water collection system permits water to be drained away from the core bit thus avoiding soiling the surrounding area. We recommend use of the water collector system with core bits of up to 250 mm. Best results are achieved in conjunction with a wet-type vacuum cleaner. Use of the water collection system in conjunction with a wet-type vacuum cleaner is mandatory for overhead drilling. The water collector seal must be of a size suitable for the core bit diameter used. Release the screw on the drill stand (at the front lower end of the column). Slide the water collector holder into place behind the screw from below. Fit the water collector between the two moveable arms of the water collector holder. Secure the water collector by way of the two screws on the water collector holder. Alternatively, the water can be allowed to flow away through a length of hose attached to the connector. Turn the hand wheel until the core bit contacts the material in which the hole is to be drilled. Set the desired drilling depth by adjusting the distance between the carriage and the depth gauge. Secure the depth gauge by tightening the clamping screw. 22 6. 3. 13 Fitting a diamond core bit (drive unit with Hilti BL chuck) ­ The core bit may become hot during use or during sharpening. Lock the carriage in position on the column (activate the carriage locking mechanism) and check that the drill stand is fastened securely. Open the chuck by turning it in the direction of the "open" symbol (open brackets). Push the connection end of the diamond core bit into the chuck on the drive unit from below until it engages with the gear teeth. [. . . ] Disposal Most of the materials from which Hilti tools or machines are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back your old machines or tools for recycling. Please ask your Hilti customer service department or Hilti sales representative for further information. [. . . ]